Home > PAINT & SUNDRIES > PAINT & STAINS > WATERPROOFERS & SEALERS
Choose a sub category:
CONCRETE SEALERS MULTI-SURFACE SEALERS MASONRY WATERPROOFERS
FOUNDATION COATINGS
Sort By:
1
WaterSeal 10100 Multi-Surface Waterproofer WaterSeal TH.024104-14 Multi-Surface Waterproofer Damtite 01071 Waterproofer Powder
Convenient waterproofing spray that provides proven waterproofing protection for wood, concrete and brick. Proven to waterproof wood, concrete and brick. Use as a wood sealer, brick sealer or for concrete waterproofing. A Portland cement-based, waterproofing coating for sealing, protecting & decorating wall sand surfaces constructed of poured concrete, concrete, cinder block, masonry, stone, brick or stucco. Safe coating for sealing the inside of drinking water concrete tanks and cisterns. Eliminates dampness, resists mold, mildew & flaking, chalking while beautifying and sealing all pores & voids. Unlike ready-mix paints which can only be applied to dry surfaces, this product is made for use on wet or dry surfaces. It also reduces Radon gas infiltration. Wear protective gloves and goggles.
WATERTITE GENERAL PURPOSE 1GA Drylok 00542 Masonry Waterproofer Henry PR1760074 Premier Foundation Coating
Zinsser Waterproofing Paint, Net Content: 1 gal, Liquid, White, Sheen: Flat, Compositions: Hydrous Magnesium Silicate, Titanium Dioxide, Dipropylene Glycol n-Propyl Ether, 2,2-Ethylenedioxydiethyl bis(2-Ethylhexanoate), Quartz, 2,2,4-Trimethyl-1,3-Pentanediol Monoisobutyrate, Aqueous Ammonia, Specific Gravity: 1.397, Flash Point: 94 deg C, VOC Content: 97 g/L, Boiling Point: 100 to 537 deg C, Flammability Rating: 1 DRYLOK? powdered masonry waterproofer is formulated to fill and seal porous masonry walls against water, even under pressure, by becoming an actual part of the original surface. An aggregate type material, DRYLOK? powdered masonry waterproofer is ideal as a base coat, as well as a finish coat. Environmentally friendly. Asphalt Emulsion. For spray or brush application to existing or new, green or damp concrete and masonry surfaces. For below-greade applications to foundations, both poured concrete and CMU block. No odor, soap and water cleanup.
WATERTITE CLEAR PAINT 1GA SEALER ACRYLIC SOLVENT GLO CLR CONCRETE WATER REPELLENT 1GA
Watertite? clear mold and mildewproof waterproofing paint forms an impermeable, smooth, non-pigmented barrier to water on bare masonry wall and floor surfaces. Intended for use on interior or exterior, vertical or horizontal, concrete block and cast-in-place concrete. Backed by a five years waterproof guarantee and mold and mildew proof paint film guarantee, it can be used to stop moisture from entering or exiting a concrete surface. Dyco? Paver Sealer? is a solvent acrylic, "non-yellowing" water-proofing sealer designed to seal and protect bare/non-sealed cement pavers. Paver Sealer? gives a wet look appearance while enhancing the true colors of the paver. Paver Sealer? resists tire markings, cracking and peeling. Paver Sealer? is easy to apply and provides a mildew-resistant barrier. Dyco? 7200 cement Paver Sealer? is a solvent acrylic, non-yellowing clear sealer for sealing non-sealed or coated pavers. Paver Sealer? gives a wet look and enhances the true color of the paver. How to determine if your pavers have been sealed with a latex water base sealer: Test the surfaces by pouring a small amount of water on the surface. If it penetrates quickly, the surface is porous and ready for 7200 Paver Sealer?. If it does not and takes 2 to 20 min to penetrate, then do not apply 7200 Paver Sealer?. Safe, odorless, clear penetrating sealer. Protects against water, ice and salt damage.
Damtite 03550 Masonry Waterproofer Gardner-Gibson 0125-GA Roof And Foundation Coating Henry RC065070 Roofers Choice Foundation Coating
High-performance masonry waterproofers used for above or below-grade applications. Alkali-resistant coating provides excellent waterproofing protection with a decorative finish for all masonry, cinder and concrete block, poured concrete, brick, stucco, basement, retaining walls and foundations. Fast drying, low odor, tintable and easy to clean up. Reduces radon gas penetration through concrete block walls. Covers up to 125 sq-ft/gal. A thin, liquid-applied coating designed to seal and penetrate exterior concrete and masonry surfaces while providing a moisture barrier. It can also be used as an anti-corrosive coating for below-grade steel or metal piping. Seals and protects wood footings from decay and termites. For exterior use only. Cures to a tough, flexible, weather-resistant film. Because of its ability to retain its pliability, the coating resists damage which may result from expansion and contraction caused by weather and temperature variation. Use as an exterior underground foundation coating and dampproofer for brick, concrete, cement block and similar surfaces. May be used as an underground exterior foundation coating and dampproofer. Covers approximately 1 to 2 gal per 100 sq-ft.
United Gilsonite 22113 Masonry Waterproofer FBRWL SURF BONDING CEM WH 50LB FBRWL SURF BONDING CEM GR 50LB
DRYLOK? natural look sealer is a non-yellowing protective coating that can be used as a sealer or concrete curing membrane. As a sealer, DRYLOK? natural look sealer penetrates deep to seal and protect masonry against acids, alkalis, road salts, de-icing compounds, household cleaners, gasoline, oil and weathering. Protects against dusting, staining and spalling. As a concrete hardener, When applied to freshly poured concrete, after the surface has set for 24 hrs and excess water has been removed, DRYLOK? natural look sealer will control water evaporation resulting in maximum concrete hardness. FiberWall? is an alkali-resistant, fiberglass-reinforced, Portland cement-base surface bonding cement with sand, used for construction of concrete block walls by dry-stack (without mortar). It is also ideal to waterproof, strengthen, rehabilitate, reinforce, restore and beautify various existing deteriorating surfaces, including chimneys, retaining walls and other concrete, brick, stone, tile or stucco areas above and below grade, on the interior and exterior. FiberWall? is an alkali-resistant, fiberglass-reinforced, Portland cement-base surface bonding cement with sand, used for construction of concrete block walls by dry-stack (without mortar). It is also ideal to waterproof, strengthen, rehabilitate, reinforce, restore and beautify various existing deteriorating surfaces, including chimneys, retaining walls and other concrete, brick, stone, tile or stucco areas above and below grade, on the interior and exterior.
LATEX WATERPROOFER WHITE 1GA Damtite 01351 Supertite Masonry Waterproofer Henry PR175070 Premier Foundation Coating
Damtite Ultima is a low-odor, high-performance masonry waterproofer with a bright white finish. Ideal for interior and exterior, above and below grade applications. This durable, alkali-resistant coating provides excellent waterproofing protection with a slightly textured, decorative finish for all masonry, cinder and concrete block, poured concrete, brick, stone, stucco, basement, garage and retaining walls and foundations. No pre-mixing or pre-wetting is needed. Stops over 25 psi of hydrostatic water pressure. Fast drying with easy soap and water clean-up. Heavy-duty, Portland cement-based waterproofing coating with dry polymer-modified additive for excellent adhesion. Eliminates need for liquid bonding additive to mix for non-porous, smooth surfaces. Ideal for sealing, protecting and decorating vertical walls and surfaces constructed of concrete, masonry, stone, brick or stucco. Eliminates dampness, resists mold/ mildew and flaking or chalking while beautifying and sealing all pores and voids. Formulated for application directly onto damp or wet surfaces. A cold applied liquid asphalt in a solvent system. Penetrating type coating formulated to provide a durable, weather-resistant film. For long-wearing protection of foundation coating. Also use to dampproofing above and below-grade exterior concrete and masonry walls and foundations that are thoroughly dry. Covers 1.5 to 2 gal per 100 sq-ft. depending upon the porosity and roughness of the surface.
Damtite 02501 Waterproof Coating Zinsser 5001 Watertite Waterproofing Paint Henry PR175042 Premier Foundation Coating
A gray Portland cement-base, waterproofing coating for sealing, protecting and decorating walls and surfaces constructed of poured concrete, concrete/cinder block, masonry, stone, brick or stucco. Ideal as parge coat for exterior, below-grade applications instead of using regular cement which does not waterproof. Safe coating for sealing the inside of drinking water concrete tanks and cisterns. WATERTITE? professional Mold and Mildew-Proof? waterproofing paint has a unique oil-base formula that combines a state-of-the-art waterproofing resin with Portland cement to create a coating that stops up to 34 lb psi of water pressure. It also contains a mildewcide to prevent the growth of mold and mildew for a minimum of 10 years after application, making it great for basements and other masonry surfaces where mold and mildew can be problematic. Premier 175 Foundation Coating Non-Fibered dries to a tough, flexible, weather resistant film. Because of its ability to retain its flexibility, resists damage which may result from expansion and contraction caused by weather, temperature variation and normal building vibration.
Damtite 01211 Waterproofer Powder Drylok 27513 Ready-To-Use Concrete Sealer Drylok 27613 Latex Based Masonry Waterproofer
A Portland cement-based, waterproofing coating for sealing, protecting & decorating wall sand surfaces constructed of poured concrete, concrete, cinder block, masonry, stone, brick or stucco. Safe coating for sealing the inside of drinking water concrete tanks and cisterns. Eliminates dampness, resists mold, mildew & flaking, chalking while beautifying and sealing all pores & voids. Unlike ready-mix paints which can only be applied to dry surfaces, this product is made for use on wet or dry surfaces. It also reduces Radon gas infiltration. Wear protective gloves and goggles. Latex Base DRYLOK? Masonry waterproofer is the manageable way to solve water seepage problems. Reduces radon gas penetration by reducing vapor transfer. Latex Base DRYLOK? Masonry waterproofer is the manageable way to solve water seepage problems. Reduces radon gas penetration by reducing vapor transfer.
Damtite 01501 Waterproof Coating SEALER CONCRETE CLEAR GAL SEALER CONCRETE GRAY GAL
Heavy-duty, Portland cement-base, waterproofing coating for sealing, protecting & decorating walls and surfaces constructed of poured concrete, concrete/cinder block, masonry, stone, brick or stucco. Safe coating for sealing the inside of drinking water concrete tanks and cisterns. Henry? 635 is a high-performance, high solids concrete sealer that is easy to apply, quick drying, nonflammable and UV stable. Applied at a minimum of two coats, Henry 635 is designed to protect all exterior absorbent concrete and masonry surfaces on residential and commercial applications, including driveways, sidewalks, patios, courtyards, walkways, pool decks and most vertical concrete surfaces. It is especially suited to seal Henry toppings and the gray version can be used to create a uniform appearance over both a repaired area and the adjacent concrete or masonry surfaces. Henry 635 is durable and abrasion-resistant when applied properly. Henry? 635 is a high-performance, high solids concrete sealer that is easy to apply, quick drying, nonflammable and UV stable. Applied at a minimum of two coats, Henry 635 is designed to protect all exterior absorbent concrete and masonry surfaces on residential and commercial applications, including driveways, sidewalks, patios, courtyards, walkways, pool decks and most vertical concrete surfaces. It is especially suited to seal Henry toppings and the gray version can be used to create a uniform appearance over both a repaired area and the adjacent concrete or masonry surfaces. Henry 635 is durable and abrasion-resistant when applied properly.
Valspar 7276 Multi-Surface Waterproofing Sealer WaterSeal 24111 Multi-Surface Waterproofer SEALER HI-GLOSS LATEX BASE
Beads water to resist moisture damage. Dries to clear finish, soap and water cleanup. Use on wood, brick, concrete, masonry, stucco and porous surfaces. Proven to waterproof wood, concrete and brick. Use as a wood sealer, brick sealer or for concrete waterproofing. DRYLOK? WetLook high-gloss sealer Just like natural and man-made stone, concrete and masonry are porous materials that will start to break down, dust, pit, crack and/or stain when subjected to weather, water, oil and UV rays. The only way to prevent damage and deterioration is to protect your surfaces with a good quality sealer. DRYLOK? wet look high-gloss sealer is a clear, non-yellowing, water-base sealer formulated for use on horizontal and vertical masonry surfaces where a high-gloss, WetLook finish is desired.
SEALER BRICK&MSNRY CLEAR 1GAL Drylok 28613 Latex Based Masonry Waterproofer WATERPROOF MASONRY GRAY 1G
DRYLOK? siloxane 7 brick and masonry penetrating sealer is a clear, durable, water-repellent, specialty formulation for use on exterior, above-grade, vertical and horizontal brick and masonry surfaces. With just one coat, it minimizes the deterioration of masonry and mortar and helps control efflorescence (salt deposits) and surface staining. DRYLOK? siloxane 7 brick and masonry penetrating sealer prevents moisture penetration and eliminates plaster cracking, paint blistering and damp staining of interior finishes. Latex base DRYLOK? EXTREME masonry waterproofer is the next generation in waterproof coatings. Features flexible encapsulated polymers which squeeze into the masonry for the ultimate in waterproof protection. Specially formulated to resist mildew growth on the dry paint film with the incorporation of an environmentally friendly green biocide. Fully transferable 15 years warranty. Tested to ASTM D-7088 Resistance to hydrostatic pressure at 15 psi and ASTM D6904 resistance to wind driven rain. Reduces Radon gas penetration. If water is leaking through existing masonry or you need to protect new construction, DRYLOK? extreme masonry waterproofer's proprietary formula is guaranteed to stop water. Unlike ordinary paint that simply adheres to a surface and can be forced off by incoming water pressure, DRYLOK? extreme masonry waterproofer actually penetrates the pores in that surface, bonding to the masonry and creating an impenetrable barrier.
WATERPROOFING PAINT M&M PRF 1G WaterSeal 24106 Multi-Surface Waterproofer Valspar 7276 Multi-Surface Waterproofing Sealer
Stop water in its tracks with RUST-OLEUM? Zinsser? WATERTITE?-LX Mold and Mildew-Proof? waterproofing paint. This low-odor, latex-based formula resists up to 20 psi of water pressure when applied to concrete or masonry, indoors or out, above- or below-grade. Proven to waterproof wood, concrete and brick. Use as a wood sealer, brick sealer or for concrete waterproofing. Beads water to resist moisture damage. Dries to clear finish, soap and water clean up. Use on wood, brick, concrete, masonry, stucco and porous surfaces.
SEALER CONCRETE WET LOOK 1 GAL SEALER CONCRETE NATRAL LOOK 1G WATERPROOFER MASONRY CLEAR 1G
ROCKSOLID? wet look concrete sealer seals and protects concrete and masonry surfaces from the damaging effects of water, chemicals and UV light. The water-base, film-forming formula provides a protective barrier to keep water out, protect against stains and extend the life of your concrete while leaving a wet look, high-gloss finish. ROCKSOLID? natural look concrete sealer seals and protects concrete and masonry surfaces from the damaging effects of water, chemicals and UV light. The water-base, film-forming formula provides a protective barrier to keep water out, protect against stains and extend the life of your concrete while leaving a natural look, low-gloss finish. Waterproof interior, exterior, above or below grade walls. Unlike ordinary paint that simply adheres to a surface and can be forced off by incoming water pressure, DRYLOK? floor and wall masonry waterproofer actually penetrates the pores in that surface, bonding to the masonry and creating an impenetrable barrier.
SEALER MULTI-SURF CWF CLEAR GA Homax 613 Wet Look Cure Seal Drylok 22115 Natural Look Sealer
CWF? multi-surface is a clear waterproofing sealant that protects against moisture damage. It is recommended for use on brick, stucco, concrete, masonry and more. Protects from oil, rust, water and sprinkler stain penetration. Use on exposed aggregate, flagstone, concrete driveway, patio tile, walkway, and garage floor. Low odor and non-flammable. Leaves a clear natural wet look. Ready for traffic 8 to 24 hours. Apply with roller, brush, sponge, mop or airless sprayer. Covers 150 to 400 sq. ft. per gallon depending on porosity. DRYLOK? natural look sealer is a non-yellowing protective coating that can be used as a sealer or concrete curing membrane. As a sealer, DRYLOK? natural look sealer penetrates deep to seal and protect masonry against acids, alkalis, road salts, de-icing compounds, household cleaners, gasoline, oil and weathering. Protects against dusting, staining and spalling. As a concrete hardener, When applied to freshly poured concrete, after the surface has set for 24 hrs and excess water has been removed, DRYLOK? natural look sealer will control water evaporation resulting in maximum concrete hardness.
MOISTURE STOP 1 GALLON Damtite 02451 Waterproofer Powder Damtite 01451 Waterproofer Powder
RUST-OLEUM Moisture stop penetrates into concrete and reacts with the free calcium and water to form a gel in cracks, pores and capillaries to protect against the ingress of water and contaminants. This allows surfaces that were previously uncoatable, due to moisture, to be coated. A Portland cement-based, waterproofing coating for sealing, protecting & decorating wall sand surfaces constructed of poured concrete, concrete, cinder block, masonry, stone, brick or stucco. Safe coating for sealing the inside of drinking water concrete tanks and cisterns. Eliminates dampness, resists mold, mildew & flaking, chalking while beautifying and sealing all pores & voids. Unlike ready-mix paints which can only be applied to dry surfaces, this product is made for use on wet or dry surfaces. It also reduces Radon gas infiltration. Wear protective gloves and goggles. A Portland cement-based, waterproofing coating for sealing, protecting & decorating wall sand surfaces constructed of poured concrete, concrete, cinder block, masonry, stone, brick or stucco. Safe coating for sealing the inside of drinking water concrete tanks and cisterns. Eliminates dampness, resists mold, mildew & flaking, chalking while beautifying and sealing all pores & voids. Unlike ready-mix paints which can only be applied to dry surfaces, this product is made for use on wet or dry surfaces. It also reduces Radon gas infiltration. Wear protective gloves and goggles.
SEALER MULTI-SURF CWF CLR 5GA WATERTITE-LX PAINT M&M PRF 3G Valspar 82390 Wet Look Sealer
CWF? multi-surface is a clear waterproofing sealant that protects against moisture damage. It is recommended for use on brick, stucco, concrete, masonry and more. Stop water in its tracks with RUST-OLEUM Zinsser? WATERTITE-LX Mold and Mildew-Proof? waterproofing paint. This low-odor, latex-based formula resists up to 20 psi of water pressure when applied to concrete or masonry, indoors or out, above- or below-grade. Valspar? wet look high-gloss sealer waterproofs and enhances the color and design of aggregate, masonry, brick, slate and pavers with a glossy, wet-look sheen. As durable as it is beautiful, it protects against the sun's powerful rays, damaging weather, water, gasoline and de-icing salts.
Valspar 82092 Natural Look Waterproofer Eagle EU1 Coat Concrete Sealer WaterSeal TH.023111-03 Waterproofer Masonry Protector
Valspar? natural look protective sealer locks out weather and scuffs with a tough, penetrating layer of invisible protection. Eagle SUPREME SEAL is a tough, clear, pure acrylic, non-yellowing sealer formulated for all types of concrete. Especially decorative, stained, stamped or colored concrete and provides a high gloss, wet-looking finish. SUPREME SEAL is solvent-based for lasting beauty and durability and will help protect your concrete against weathering and erosion. Provides proven waterproofing protection for all masonry surfaces including pavers, brick, concrete, stone, stucco, clay and quarry tile. Use for concrete waterproofing and as a brick sealer.
Eagle EB5 Coat Concrete Sealer Eagle EU5 Coat Concrete Sealer Drylok 27515 Latex Based Masonry Waterproofer
Eagle PREMIUM COAT is a premium solvent-based concrete sealer specifically formulated for exposed aggregate concrete. This high solids, styrene-acrylic co-polymer solution is formulated to achieve both a protective and decorative finish. Along with protecting concrete surfaces against water seepage and aggregate loosening, Eagle PREMIUM COAT beautifies the surface with a high gloss finish that shines and darkens as it protects. Eagle is a premium solvent-based concrete sealer specifically formulated for exposed aggregate concrete. This high solids, styrene-acrylic co-polymer solution is formulated to achieve both a protective and decorative finish. Along with protecting concrete surfaces against water seepage and aggregate loosening, Eagle beautifies the surface with a high gloss finish that shines and darkens as it protects. Latex Base DRYLOK? Masonry waterproofer is the manageable way to solve water seepage problems. Reduces radon gas penetration by reducing vapor transfer.
Drylok 27615 Masonry Waterproofing Paint Valspar 82390 Wet Look Sealer Valspar 82092 Natural Look Waterproofer
Latex Base DRYLOK? Masonry waterproofer is the manageable way to solve water seepage problems. Reduces radon gas penetration by reducing vapor transfer. Valspar wet look high gloss sealer waterproofs and enhances the color and design of concrete, brick, masonry, slate and pavers with a glossy, wet-look sheen. This sealer is formulated to protect your exterior surfaces against the sun's UV rays and damaging weather. Resists gasoline, oil and de-icing salts. Valspar natural look waterproofer forms a long lasting, waterproofing seal on concrete, brick, masonry, aggregate, natural stone and pavers. This sealer is formulated to protect against the sun's UV rays, water, gasoline and de-icing salts. This protective sealer allows the natural look of the surface to come through.
Cabot 1000 Waterproofing Sealer Zinsser Watertite Waterproofing Paint Damtite 03555 Masonry Waterproofer
Cabot waterproofing is an advanced technology silicone sealer that provides unsurpassed waterproofing protection to a multitude of surfaces. This convenient and simple-to-use formulation penetrates and fills the pores of the substrate with a premium-grade silicone sealer and unlike waxes, silicone will impart a lasting repellency to any surface to which it is applied. ZINSSER? WATERTITE? mold and mildew-resistant waterproofing paint is a low odor, oil-based waterproofing paint designed to waterproof interior and exterior concrete, stucco, cement, cinder block and other masonry surfaces. It is ideal for interior basement walls and for sealing concrete basement slabs prior to installing flooring. It is not recommended for foot traffic. It is also ideal for exterior foundations and retaining walls, above and below-grade. High-performance masonry waterproofers used for above or below-grade applications. Alkali-resistant coating provides excellent waterproofing protection with a decorative finish for all masonry, cinder and concrete block, poured concrete, brick, stucco, basement, retaining walls and foundations. Fast drying, low odor, tintable and easy to clean up. Reduces radon gas penetration through concrete block walls. Covers up to 125 sq-ft/gal.
Cabot 1000 Waterproofing Sealer Drylok 28615 Extreme Masonry Waterproofing Paint LATEX WATERPROOFER WHITE 5GA
Cabot waterproofing is an advanced technology silicone sealer that provides unsurpassed waterproofing protection to a multitude of surfaces. This convenient and simple-to-use formulation penetrates and fills the pores of the substrate with a premium-grade silicone sealer and unlike waxes, silicone will impart a lasting repellency to any surface to which it is applied. Latex base Drylok? Extreme masonry waterproofer is the next generation in waterproof coatings. Features flexible encapsulated polymers which squeeze into the masonry for the ultimate in waterproof protection. Specially formulated to resist mildew growth on the dry paint film with the incorporation of an environmentally friendly green biocide. Fully transferable 15 years warranty. Tested to ASTM D-7088 Resistance to hydrostatic pressure at 15 psi and ASTM D6904 resistance to wind driven rain. Reduces Radon gas penetration. Damtite ULTIMA is a low-odor latex masonry waterproofer, formulated with mildewcide to prevent mold/mildew growth on a dry paint film and with ceramic to provide a whiter, smoother finish. For interior and exterior, above & below grade applications. Durable, alkali-resistant coating provides excellent waterproofing protection with a decorative finish for all masonry, cinder and concrete block, poured concrete, brick, stucco, basement, garage and retaining walls and foundations. No pre-mixing or pre-wetting is needed. Fast drying with easy soap and water cleanup. Stops 30 psi of hydrostatic pressure. Includes fully transferable 15 year warranty.
WATERPROOF MASONRY WHITE 5G STAIN&SEALER HAMPTON GRAY 1GA STAIN&SEALER CASHMERE BRN 1GA
Waterproof interior, exterior, above or below grade walls. Unlike ordinary paint that simply adheres to a surface and can be forced off by incoming water pressure, DRYLOK? floor and wall masonry waterproofer actually penetrates the pores in that surface, bonding to the masonry and creating an impenetrable barrier. Cabot heat-reducing solid color stain and sealer with Cool Feel Technology offers durable, even color that blocks UV rays, deflects the sun's heat and reduces surface temperature by 20 deg F. Available in three colors, it covers old stains and mismatched boards with long-lasting waterproofing, exceptional washability and advanced UV protection from sun damage. Cabot heat-reducing solid color stain and sealer with Cool Feel Technology offers durable, even color that blocks UV rays, deflects the sun's heat and reduces surface temperature by 20 deg F. Available in three colors, it covers old stains and mismatched boards with long-lasting waterproofing, exceptional washability and advanced UV protection from sun damage.
STAIN&SEALER EQUESTRIAN BRN 1G SEALER ACRYLIC SOLVENT GLO CLR
Cabot heat-reducing solid color stain and sealer with Cool Feel Technology offers durable, even color that blocks UV rays, deflects the sun's heat and reduces surface temperature by 20 deg F. Available in three colors, it covers old stains and mismatched boards with long-lasting waterproofing, exceptional washability and advanced UV protection from sun damage. Dyco? Paver Sealer? is a solvent acrylic, "non-yellowing" water-proofing sealer designed to seal and protect bare/non-sealed cement pavers. Paver Sealer? gives a wet look appearance while enhancing the true colors of the paver. Paver Sealer? resists tire markings, cracking and peeling. Paver Sealer? is easy to apply and provides a mildew-resistant barrier. Dyco? 7200 cement Paver Sealer? is a solvent acrylic, non-yellowing clear sealer for sealing non-sealed or coated pavers. Paver Sealer? gives a wet look and enhances the true color of the paver. How to determine if your pavers have been sealed with a latex water base sealer: Test the surfaces by pouring a small amount of water on the surface. If it penetrates quickly, the surface is porous and ready for 7200 Paver Sealer?. If it does not and takes 2 to 20 min to penetrate, then do not apply 7200 Paver Sealer?.
   
 
1