Home > POWER TOOLS & ACC > AIR COMPRESSORS, TOOLS & ACCES > COMPRESSORS & ACCESSORIES
Choose a sub category:
AIR COMPRESSORS AIR TOOLS AIR TOOL ACCESSORIES
AIR COMPRESSOR HOSES AIR COMPRESSOR HOSE FITTINGS BLOW GUNS
AIR COMPRESSOR ACCESSORIES SPRAY GUNS AIR TANKS
Sort By:
1
Tru-Flate 21-147 Air Hose Fitting Plews 21-557 Drain Cock Tru-Flate 12-125 Hose Plug
All brass construction resists rust and will not corrode as easily as other materials. Precision machined to high-quality standards. Use with hose clamp or ferrules. For use in low pressure applications. Hand tightening provides leak-proof metal to metal seal. Corrosion-resistant brass. The Tru-Flate design plug is recognized by the extremely short pilot, however it has the widest metal section between the groove and the pilot. The sealing surface on the end of the plug is wider than other interchanges, resulting in better sealing and longer seal life. The Tru-Flate design coupler utilizes the tubular valve which supports the seal and allows more air flow at lower pressure drops than most competitive couplers. The protective collar guards against accidental disconnect.
Tru-Flate 12-225 Air Line Plug Tru-Flate 12-325 Air Line Plug Stanley THREADTAPE Thread Sealant Tape
Adopted by most coupler manufacturers, this plug design is considered the industrial standard. It can be identified by the 3/16 in pilot and flat bottom V-shaped ball groove. Conforms to ANSI (NFPA) T3.20.14-1990 dimensions. This design is identified by a 5/16 in pilot and ball groove which is nearly round. It is similar in appearance to the industrial Interchange and care must be taken to correctly identify. Couplers are available in both standard and push to connect style sleeve. Properly seals all male threaded connections to prevent air leaks.
Tru-Flate 12-135 Air Line Nipple Tru-Flate 12-235 Air Line Plug Tru-Flate 12-335 Air Line Plug
The Tru-Flate design plug is recognized by the extremely short pilot, however it has the widest metal section between the groove and the pilot. The sealing surface on the end of the plug is wider than other interchanges, resulting in better sealing and longer seal life. The Tru-Flate design coupler utilizes the tubular valve which supports the seal and allows more air flow at lower pressure drops than most competitive couplers. The protective collar guards against accidental disconnect. Adopted by most coupler manufacturers, this plug design is considered the industrial standard. It can be identified by the 3/16 in pilot and flat bottom V-shaped ball groove. Conforms to ANSI (NFPA) T3.20.14-1990 dimensions. This design is identified by a 5/16 in pilot and ball groove which is nearly round. It is similar in appearance to the industrial Interchange and care must be taken to correctly identify. Couplers are available in both standard and push to connect style sleeve.
Tru-Flate 21-123 Air Hose Fitting Tru-Flate 21-143 Air Hose Fitting Tru-Flate 21-423 Barb Hose Splicer
All brass construction resists rust and will not corrode as easily as other materials. Precision machined to high-quality standards. Use with hose clamp or ferrules. All brass construction resists rust and will not corrode as easily as other materials. Precision machined to high-quality standards. Use with hose clamp or ferrules. All brass construction resists rust and will not corrode as easily as other materials. Precision machined to high-quality standards. Use with hose clamp or ferrules.
Tru-Flate 21-595 Hose Adapter with Ball Socket Tru-Flate 21-515 Air Line Coupling Tru-Flate 21-535 Air Hose Bushing
All brass, corrosion-resistant material. This complete line of pipe couplings, thread Adapters and bushings allows user to adjust thread sizes from 1/8 in NPT through 1/2 in NPT with either male or female ends. All brass, corrosion-resistant material. This complete line of pipe couplings, thread Adapters and bushings allows user to adjust thread sizes from 1/8 in NPT through 1/2 in NPT with either male or female ends. All brass, corrosion-resistant material. This complete line of pipe couplings, thread Adapters and bushings allows user to adjust thread sizes from 1/8 in NPT through 1/2 in NPT with either male or female ends.
Tru-Flate 21-222 Air Hose Fitting Tru-Flate 17-369 Ball Foot Direct Air Line Chuck Stanley TIRE-14F Tire Chuck
All brass construction resists rust and will not corrode as easily as other materials. Precision machined to high-quality standards. Use with hose clamp or ferrules. Direct air line chucks have a built-in shut-off valve and therefore cannot be used on inflator gauges. Use when air supply lines come directly from the compressor with no other valve in the line. This tire chuck can connect to an air compressor with an adapter and be used to fill tires with air. Depend on this tire chuck for strength and durability.
Tru-Flate 21-133 Air Hose Fitting Tru-Flate 21-467 Barb Hose Splicer Stanley 38M-14M Hex Reducer Nipple
All brass construction resists rust and will not corrode as easily as other materials. Precision machined to high-quality standards. Use with hose clamp or ferrules. All brass construction resists rust and will not corrode as easily as other materials. Precision machined to high-quality standards. Use with hose clamp or ferrules. Connects FPT to FPT. Use thread sealant tape on all male threads for air-tight connections.
Tru-Flate 12-527 Air Line Plug Tru-Flate 12-603 Air Line Plug Tru-Flate 12-605 Air Line Plug
Adopted by most coupler manufacturers, this plug design is considered the industrial standard. It can be identified by the 3/16 in pilot and flat bottom V-shaped ball groove. Conforms to ANSI (NFPA) T3.20.14-1990 dimensions. The Tru-Flate design plug is recognized by the extremely short pilot, however it has the widest metal section between the groove and the pilot. The sealing surface on the end of the plug is wider than other interchanges, resulting in better sealing and longer seal life. The Tru-Flate design coupler utilizes the tubular valve which supports the seal and allows more air flow at lower pressure drops than most competitive couplers. The protective collar guards against accidental disconnect. The Tru-Flate design plug is recognized by the extremely short pilot, however it has the widest metal section between the groove and the pilot. The sealing surface on the end of the plug is wider than other interchanges, resulting in better sealing and longer seal life. The Tru-Flate design coupler utilizes the tubular valve which supports the seal and allows more air flow at lower pressure drops than most competitive couplers. The protective collar guards against accidental disconnect.
Tru-Flate 12-537 Air Hose Plug Tru-Flate 12-425 Air Line Plug Tru-Flate 12-435 Air Line Plug
Adopted by most coupler manufacturers, this plug design is considered the industrial standard. It can be identified by the 3/16 in pilot and flat bottom V-shaped ball groove. Conforms to ANSI (NFPA) T3.20.14-1990 dimensions. This plug is the most easily recognized design. The long 3/4 in pilot is so distinctive it cannot be confused with any other designs. Couplers are available in sleeve type only. This plug is the most easily recognized design. The long 3/4 in pilot is so distinctive it cannot be confused with any other designs. Couplers are available in sleeve type only.
Tru-Flate 17-351 Ball Foot Direct Air Line Chuck Tru-Flate 17-361 Ball Foot Direct Combination Air Line Chuck Tru-Flate 41-300 Hose Repair Kit
Direct air line chucks have a built-in shut-off valve and therefore cannot be used on inflator gauges. Use when air supply lines come directly from the compressor with no other valve in the line. Direct air line chucks have a built-in shut-off valve and therefore cannot be used on inflator gauges. Use when air supply lines come directly from the compressor with no other valve in the line. Contains all parts necessary to repair a direct air line hose assembly. Each kit contains one single foot air chuck, 1/4 in female NPT, one male hose end 1/4 in ID hose x 1/4 in NPT, one hose splicer, 1/4 in ID hose, three band style hose clamps, fits 3/8 in ID hose.
Plews/Edelmann 12-227/6  Air Compressor Hose Fittings Tru-Flate 21-242 Air Hose Fitting Tru-Flate 21-505 Air Line Coupling
Adopted by most coupler manufacturers, this plug design is considered the industrial standard. It can be identified by the 3/16 in pilot and flat bottom V-shaped ball groove. Conforms to ANSI (NFPA) T3.20.14-1990 dimensions. All brass construction resists rust and will not corrode as easily as other materials. Precision machined to high-quality standards. Use with hose clamp or ferrules. All brass, corrosion-resistant material. This complete line of pipe couplings, thread Adapters and bushings allows user to adjust thread sizes from 1/8 in NPT through 1/2 in NPT with either male or female ends.
3-IN-ONE 120046 Pneumatic Tool Oil PLUG 3/8IN TF X 3/8IN FNPT    Stanley AP-38F Auto Hose Adapter
Marksman spout for easy precision application. Professional-grade formula. Lubricates and protects to extend tool life. Quickly removes gum and sludge. Prevents rust. The Tru-Flate design plug is recognized by the extremely short pilot, however it has the widest metal section between the groove and the pilot. The sealing surface on the end of the plug is wider than other interchanges, resulting in better sealing and longer seal life. The Tru-Flate design coupler utilizes the tubular valve which supports the seal and allows more air flow at lower pressure drops than most competitive couplers. The protective collar guards against accidental disconnect. This automotive 3/8 in Series plug 3/8 in NPT female thread has a pre-applied thread sealant for air-tight connections. Depend on this automotive 3/8 in Series plug 3/8 in NPT female thread for durability and reliability.
Plews/Edelmann 12-611  Air Compressor Hose Fittings Stanley AP-38M Auto Hose Adapter ProSource FDQ910 Inflation Kit
PLUG AUTO 3/8IN MPT
Our Price: $5.69
The Tru-Flate design plug is recognized by the extremely short pilot, however it has the widest metal section between the groove and the pilot. The sealing surface on the end of the plug is wider than other interchanges, resulting in better sealing and longer seal life. The Tru-Flate design coupler utilizes the tubular valve which supports the seal and allows more air flow at lower pressure drops than most competitive couplers. The protective collar guards against accidental disconnect. Plated steel construction with drag guard for job site durability and reliability. Pre applied thread sealant for airtight connections. ProSource Air Inflation Kit, Brass/Steel, Brass/Silver, Brass/Nickel Plated, Includes: Inflation Adapter, Tapered Inflation Nozzle, Inflation Needle and Tire Nozzle
Marvel Mystery MM080R Air Tool Oil With Childproof Cap Stanley-Bostitch BTFP72333  Air Compressor Hose Swivel Plug - Male Tru-Flate 12-705 Air Line Plug
We added to the original MARVEL Mystery? oil to create a specially formulated tool oil for use in all piston type and rotary air tools, as well as in-line air lubricators. MARVEL? air tool oil prevents rust formation in air tools while providing positive lubrication for smoother starting, longer lasting tools. MARVEL? air tool oil assures the maximum performance of your tools by dissolving gum and sludge that reduce tools speed and power. Swivel design minimizes hose twisting for improved control. Corrosion-resistant steel. Pre-applied thread connections. The Tru-Flate design plug is recognized by the extremely short pilot, however it has the widest metal section between the groove and the pilot. The sealing surface on the end of the plug is wider than other interchanges, resulting in better sealing and longer seal life. The Tru-Flate design coupler utilizes the tubular valve which supports the seal and allows more air flow at lower pressure drops than most competitive couplers. The protective collar guards against accidental disconnect.
Tru-Flate 13-225 Air Line Coupler Tru-Flate 13-235 Industrial Air Line Coupler SPLICER HOSE REUSABLE 1/4IN
Adopted by most coupler manufacturers, this plug design is considered the industrial standard. It can be identified by the 3/16 in pilot and flat bottom V-shaped ball groove. Conforms to ANSI (NFPA) T3.20.14-1990 dimensions. Adopted by most coupler manufacturers, this plug design is considered the industrial standard. It can be identified by the 3/16 in pilot and flat bottom V-shaped ball groove. Conforms to ANSI (NFPA) T3.20.14-1990 dimensions. Flexzilla? Pro Reusable Fittings and Splicers allow you to quickly repair Flexzilla hose on the job site or create a custom length hose in just three easy steps.
Blaster 16-ATL Air Tool Lubricant HOSE AIR END REUSABLE 1/4IN   Tru-Flate 13-125 Air Line Coupler
B'LASTER air tool lubricant lubricates and protects internal tool parts. It ensures maximum tool performance, prevents unnecessary maintenance and also protects tool parts from high-speeds and shock loads. Flexzilla? Pro reusable fittings and splicers allow you to quickly repair Flexzilla hose on the job site or create a custom length hose in just three easy steps. The Tru-Flate design plug is recognized by the extremely short pilot, however it has the widest metal section between the groove and the pilot. The sealing surface on the end of the plug is wider than other interchanges, resulting in better sealing and longer seal life. The Tru-Flate design coupler utilizes the tubular valve which supports the seal and allows more air flow at lower pressure drops than most competitive couplers. The protective collar guards against accidental disconnect.
Tru-Flate 13-135 Air Line Coupler Tru-Flate 13-201 Coupler/Plug Set Tru-Flate 17-355 Snap Clip On Air Line Chuck
The Tru-Flate design plug is recognized by the extremely short pilot, however it has the widest metal section between the groove and the pilot. The sealing surface on the end of the plug is wider than other interchanges, resulting in better sealing and longer seal life. The Tru-Flate design coupler utilizes the tubular valve which supports the seal and allows more air flow at lower pressure drops than most competitive couplers. The protective collar guards against accidental disconnect. This plug design has been adopted by most coupler manufacturers. For this reason it is considered the industrial standard. It can be identified by the 3/16 in pilot and flat bottom V-shaped ball groove. Conforms to ANSI (NFPA) T3.20.14-1990 dimensions. Direct air line chucks have a built-in shut-off valve and therefore cannot be used on inflator gauges. Use when air supply lines come directly from the compressor with no other valve in the line.
Tru-Flate 13-335 Air Line Coupler SPLICER HOSE REUSABLE 3/8IN   Tru-Flate 13-325 Air Line Coupler
This design is identified by a 5/16 in pilot and ball groove which is nearly round. It is similar in appearance to the industrial Interchange and care must be taken to correctly identify. Couplers are available in both standard and push to connect style sleeve. Flexzilla? Pro Reusable Fittings and Splicers allow you to quickly repair Flexzilla hose on the job site or create a custom length hose in just three easy steps. This design is identified by a 5/16 in pilot and ball groove which is nearly round. It is similar in appearance to the industrial Interchange and care must be taken to correctly identify. Couplers are available in both standard and push to connect style sleeve.
COUPLER UNIVERSAL 1/4IN MPT   COUPLER UNIVERSAL 1/4IN FPT   HOSE AIR END REUSABLE 3/8IN
Can be used with T, I/M and A Design 1/4 in plugs, eliminating confusion among designs. Deluxe push to-connect style makes coupling quick and easy. Heavy-duty brass or composite construction means longer life. Unique tubular valve design allows greater air flow, up to 35 cfm. Can be used with T, I/M and A Design 1/4 in plugs, eliminating confusion among designs. Deluxe push to-connect style makes coupling quick and easy. Heavy-duty brass or composite construction means longer life. Unique tubular valve design allows greater air flow, up to 35 cfm. Flexzilla? Pro reusable fittings and splicers allow you to quickly repair Flexzilla hose on the job site or create a custom length hose in just three easy steps.
Plews/Edelmann 18-603 Air Blow Guns Plews/Edelmann 41-101 Air Tool Oilers Stanley-Bostitch BTFP72321  Air Compressor Hose Coupler
Adjust from low air to a full volume flow. Recommended air pressure to 150 psi maximum. Knurled nozzle makes handling easy. Complete with handy pocket clip. Fits all industrial/Milton design 1/4 in coupler bodies. Prevents burn-out, stops rust and increases torque up to 25%. A compact oiler that fastens directly to the air tool. Precisely meters proper amount of oil to the tool only when the tool is in use. NO adjustments necessary 1/4 in male NPT outlet, 1/4 in female NPT inlet. Use on all 3/8 and 1/2 in air impact guns, air wrenches, body shop air tools and pneumatic hammers. Note: never use motor oil in pneumatic tool. This plated, steel industrial Series plug is designed for strong connections. Thread sealant is pre-applied to prevent leakage. Depend on this industrial Series plug for durability.
SPLICER HOSE REUSABLE 1/2IN   Stanley IC-14M Industrial Hose Adapter Stanley IC-14F Industrial Hose Adapter
Flexzilla? Pro Reusable Fittings and Splicers allow you to quickly repair Flexzilla hose on the job site or create a custom length hose in just three easy steps. This 1/4 in NTP male thread is tough and durable. It is designed for secure and balanced connections. Air-tight connections and plated steel construction makes it reliable for professional jobs. This 1/4 in NTP female thread is tough and durable. It is designed for secure and balanced connections. Air-tight connections and plated steel construction makes it reliable for professional jobs.
Blaster 16-ATC Air Tool Conditioner Stanley-Bostitch BTFP72320  Air Compressor Hose FittingsSeries Coupler Tru-Flate 17-353 Ball Foot Direct Clip On Air Line Chuck
B'LASTER air tool conditioner thoroughly cleans internal pneumatic tool parts, restoring them to peak performance and prolonging tool life. It breaks loose deposits that create friction and impede smooth operation. It also provides long-lasting lubrication and protects tools from freeze up. This plated, steel industrial Series plug is designed for strong connections. Thread sealant is pre-applied to prevent leakage. Depend on this industrial Series plug for durability. Direct air line chucks have a built-in shut-off valve and therefore cannot be used on inflator gauges. Use when air supply lines come directly from the compressor with no other valve in the line.
Tru-Flate 21-605 Barb Air Line Swivel HOSE AIR END REUSABLE 1/2IN   Stanley HREPAIR-38 Hose Splice Kit
Eliminates kinked and twisted air line hose by swiveling a full 360 deg. Use on air lines, tools and compressor connections to increase flexibility and convenience. Barb type and male/female connections. 150 psi maximum working pressure. Flexzilla? Pro reusable fittings and splicers allow you to quickly repair Flexzilla hose on the job site or create a custom length hose in just three easy steps. Kit includes one 1/4 in MPT x barbed hose splicer for 3/8 in hose one barb x barb hose splicer for 3/8 in hose & three clamps.
Stanley Industrial IHKIT-14F Hose Coupler Kit Tru-Flate 13-203 Coupler/Plug Kit Bostitch BTFP72327 Ball Drain Valve
This 1/4 in Series hose coupler kit is tough and durable. It is designed for secure and balanced connections. Air-tight connections and plated steel construction makes it reliable for professional jobs. This plug design has been adopted by most coupler manufacturers. For this reason it is considered the industrial standard. It can be identified by the 3/16 in pilot and flat bottom V-shaped ball groove. Conforms to ANSI (NFPA) T3.20.14-1990 dimensions. Bostitch Ball Drain Valve, Specifications: 1/4 in MNPT Connection
Plews/Edelmann 13-237 Hose Coupling Stanley TEE-14F Tee Fitting Plews/Edelmann 18-231 Tru-Flate Air Blow Guns
Adopted by most coupler manufacturers, this plug design is considered the industrial standard. It can be identified by the 3/16 in pilot and flat bottom V-shaped ball groove. Conforms to ANSI (NFPA) T3.20.14-1990 dimensions. Use this tee fitting 1/4 in NPT female thread for joining pipes of varying diameters or for changing the direction a pipe runs. Depend on this tee fitting 1/4 in female thread for strength and durability. Conforms to all Federal requirements related to OSHA, including noise level regulations. Tamperproof pressure reducers built into this gun limit nozzle pressure to 30 psi or less when used with listed inlet pressure. Features vented nozzle to relieve the compressed air should the nozzle become plugged or accidentally obstructed. Heavy-duty die-cast, epoxy finish body. Complete with hang-up hook and 1/4 in female NPT inlet.
Marvel Mystery MM85R1 Air Tool Oil With Childproof Cap Tru-Flate 17-383 Dual Foot Direct Air Line Chuck HOSE AIR END REUSABLE 1/4IN
We added to the original MARVEL Mystery? oil to create a specially formulated tool oil for use in all piston type and rotary air tools, as well as in-line air lubricators. MARVEL? air tool oil prevents rust formation in air tools while providing positive lubrication for smoother starting, longer lasting tools. MARVEL? air tool oil assures the maximum performance of your tools by dissolving gum and sludge that reduce tools speed and power. Direct air line chucks have a built-in shut-off valve and therefore cannot be used on inflator gauges. Use when air supply lines come directly from the compressor with no other valve in the line. Flexzilla? Pro Reusable Fittings and Splicers allow you to quickly repair Flexzilla hose on the job site or create a custom length hose in just three easy steps.
HOSE AIR ED RUSBL W/SWVL 3/8IN Bostitch Prozhoze Reusable Hose Repair Kit Stanley BTFP72330 Safety Blow Gun
Flexzilla? Pro reusable fittings and splicers allow you to quickly repair Flexzilla hose on the job site or create a custom length hose in just three easy steps. Includes 1 mender and 1 threaded end fittings. Simple 3-step process includes unscrew, cut and replace. Safety blow gun.
Tru Flate 18-143 Clip-On Safety Blow Gun Plews/Edelmann 18-319 Tru-Flate Air Safety Blow Guns Stanley 3WAY-RND 3-Way Round Air Line Manifold
MANIFOLD 3WAY 1/4IN
Our Price: $10.99
Converts any standard ball foot tire chucks to a safety blowgun. Vented nozzle and built-in pressure reduces limit nozzle pressure to a maximum of 30 psi, with up to 150 psi inlet pressure. Conforms to #1001 OSHA regulation. Epoxy finish. Vented nozzle to relieve the compressed air should the nozzle become plugged or accidentally obstructed. Heavy-duty die-cast body. Hang up hook and 1/4 in NPT female inlet included. Meets OSHA regulation 1001 for 30 psi "dead head" pressure. Inlet pressure rating of 150 psi. "Splits single air line into three for running multiple air tools. Use 3/8"" male threaded inlet fitting for maximum performance. Aluminum."
ProSource DZA019 Hose Coupler Set Tru-Flate 13-301 Coupler/Plug Set Tru-Flate 13-537 Air Line Coupler
Contains 5-pcs: 3-piece 1/4 in MPT quick plug, 1-piece 1/4 in FPT quick plug and 1-piece 1/4 in NPT quick coupler. This design is identified by a 5/16 in pilot and ball groove which is nearly round. It is similar in appearance to the industrial interchange and care must be taken to correctly identify. Couplers are available in both standard and push to connect style sleeve. This plug design has been adopted by most coupler manufacturers. For this reason it is considered the industrial standard. It can be identified by the 3/16 in pilot and flat bottom V-shaped ball groove. Conforms to ANSI (NFPA) T3.20.14-1990 dimensions.
Tru-Flate 13-611 Air Line Coupler Tru-Flate 13-527 Air Coupler HOSE AIR ED RUSBL W/SWVL 1/2IN
The Tru-Flate design plug is recognized by the extremely short pilot, however it has the widest metal section between the groove and the pilot. The sealing surface on the end of the plug is wider than other interchanges, resulting in better sealing and longer seal life. The Tru-Flate design coupler utilizes the tubular valve which supports the seal and allows more air flow at lower pressure drops than most competitive couplers. The protective collar guards against accidental disconnect. Tru-Flate Air Coupler, Industrial, Specifications: 3/8 in Connection, Inverted Male x MNPT Connection Type, Steel Flexzilla? Pro reusable fittings and splicers allow you to quickly repair Flexzilla hose on the job site or create a custom length hose in just three easy steps.
Stanley PRECOMOIL-32OZ Pneumatic Tool Lubricant Tru-Flate 41-125 3-Way 3-in-1 Air Line Manifold Campbell Hausfeld ST127012AV Air Tool Oil
Bostitch Pneumatic Tool Lubricant, Net Content: 32 oz, Bottle PLEWS/EDELMANN Air Line Manifold, 3-Way, 3-in-1, Nominal Size: 1/4 in, NPT Connection Campbell Hausfeld air tool oil (ST127012AV) helps prolong air tool life by providing vital lubrication. Specially formulated to maximize tool performance. Use daily by applying several drops in tool air inlet.
Plews 4-25E-RET Recoil Air Hose Tru-Flate 13-101 Coupler/Plug Set Tru-Flate 13-613 Air Line Coupler
Nylon recoil hose retains its self-coiling properties and stores itself when finished. Can be used with all air-powered equipment on the jobsite and in garages, plants and service stations. The swivel end fittings reduce hose twist. The Tru-Flate design plug is recognized by the extremely short pilot; however, it has the widest metal section between the groove and the pilot. The sealing surface on the end of the plug is wider than other interchanges, resulting in better sealing and longer seal life. The Tru-Flate design coupler utilizes the tubular valve which supports the seal and allows more air flow at lower pressure drops than most competitive couplers. The protective collar guards against accidental disconnect. The Tru-Flate design plug is recognized by the extremely short pilot, however it has the widest metal section between the groove and the pilot. The sealing surface on the end of the plug is wider than other interchanges, resulting in better sealing and longer seal life. The Tru-Flate design coupler utilizes the tubular valve which supports the seal and allows more air flow at lower pressure drops than most competitive couplers. The protective collar guards against accidental disconnect.
Tru-Flate 17-373 Grip Tite Direct Air Line Chuck ProSource CC970 Air Blow Gun Tru Flate 18-233 Safety Blow Gun
Direct air line chucks have a built-in shut-off valve and therefore cannot be used on inflator gauges. Use when air supply lines come directly from the compressor with no other valve in the line. Ideal for cleaning damaging dirt and grime buildups from large machinery, engines and heavy equipment. Increased performance and yet still meets OSHA regulation 100-1 for 30 psi "dead head" pressure. Features vented nozzle to relieve the compressed air should the nozzle become plugged or accidentally obstructed. Heavy-duty die-cast body. Complete with hang-up hook and 1/4 in NPT female inlet. Inlet pressure of 150 psi.
Tru-Flate 13-435 Air Line Coupler Tru-Flate 24-801 Air Line Pressure Gauge Stanley UC38-14F Push-to-Connect Auto Hose Adapter
This plug is the most easily recognized design. The long 3/4 in pilot is so distinctive it cannot be confused with any other designs. Couplers are available in sleeve type only. Pressure rating of 0 to 200, 0 to 14 kg/sq-cm and mounting back. This push-to-connect Series coupler is universal to fit many application needs and enables you to connect two 1/4 in MNPT threads. Forget about thread seal tape and pipe dope, this hex nipple is designed to keep tapered threads air-tight with its pre-applied thread sealant.
Stanley-Bostitch BTFP72318  Air Compressor Hose Fittings Plug - Male Stanley-Bostitch BTFP72319  Air Compressor Hose Fittings Plug - Female Tru-Flate 13-425 Air Line Coupler
This plated, steel industrial Series plug is designed for strong connections. Thread sealant is pre-applied to prevent leakage. Depend on this industrial Series plug for durability. Pre-applied thread sealant for airtight connections. Simplifies field installation by eliminating the need for thread sealant tape. Plated steel construction with drag guard for jobsite durability and reliability. 6-ball coupler design for balanced, strong and secure connections. This plug is the most easily recognized design. The long 3/4 in pilot is so distinctive it cannot be confused with any other designs. Couplers are available in sleeve type only.
HOSE AIR END REUSABLE 3/8IN   Stanley UC38-14M Push-to-Connect Auto Hose Adapter Tru Flate 18-207 Standard Blow Gun
Tru-Flate 18-207 Blow Gun
Our Price: $14.99
Flexzilla? Pro reusable fittings and splicers allow you to quickly repair Flexzilla hose on the job site or create a custom length hose in just three easy steps. This push-to-connect Series coupler is universal to fit many application needs and enables you to connect two 1/4 in MNPT threads. Forget about thread seal tape and pipe dope, this hex nipple is designed to keep tapered threads air-tight with its pre-applied thread sealant. Allows full line pressure to be used. Oil-resistant, soft replaceable rubber tip. Will not mar delicate surfaces. Gives a leakproof seal against oil passages, fuel lines and more. When air pressure is needed for cleaning.
Campbell Hausfeld ST125312AV Air Compressor Tool Oil Plews 4-50E-RET Recoil Air Hose Tru Flate 18-203 Standard Blow Gun
Tru-Flate 18-203 Blow Gun
Our Price: $15.99
Campbell Hausfeld air compressor oil (ST125312AV) is a high-quality, 30-weight, non-detergent, single-viscosity oil that provides the lubrication air compressors require. Ideal for all brands and models of oil-lubricated air compressors, this oil can prolong pump life by reducing valve carbon build up. Nylon recoil hose retains its self-coiling properties and stores itself when finished. Can be used with all air-powered equipment on the jobsite and in garages, plants and service stations. The swivel end fittings reduce hose twist. Comfortable thumb lever valve control with handy hanger in lever and hanger hook. Compact one-piece nozzle. Allows full line pressure to be used. Includes 1/4 in female NPT inlet. To comply with OSHA regulations standard blowguns must be used on a regulated air line with a pressure setting not to exceed 30 psi.
Plews 576-25A Air Hose BLOWGUN SET 2PC               Plews/Edelmann 18-302 Tru-Flate Air Safety Blow Guns
Amflo? PVC air hose is ideal for general-purpose applications. It features a lightweight, flexible, kink-resistant design with bend restrictors. Its bright florescent colors reduce chances of tripping while on a jobsite. Tru-Flate Hi Flo? blowguns combine ergonomics with power for an enhanced experience. Meets OSHA regulation 100-1 for 30 psi "dead head" pressure. Features vented nozzle to relieve the compressed air should the nozzle become plugged or accidentally obstructed. Heavy-duty die-cast body with hang-up hook, 1/4 in NPT female inlet and 4 in extension.
Bostitch Prozhoze Reusable Hose Repair Kit Plews/Edelmann 13-603 Hose Coupling Plews/Edelmann 13-605 Hose Coupling
Includes 1 mender and 1 threaded end fittings. Simple 3-step process: unscrew, cut and replace. Includes 1mender and 1 threaded end fitting. The Tru-Flate design plug is recognized by the extremely short pilot, however it has the widest metal section between the groove and the pilot. The sealing surface on the end of the plug is wider than other interchanges, resulting in better sealing and longer seal life. The Tru-Flate design coupler utilizes the tubular valve which supports the seal and allows more air flow at lower pressure drops than most competitive couplers. The protective collar guards against accidental disconnect. The Tru-Flate design plug is recognized by the extremely short pilot, however it has the widest metal section between the groove and the pilot. The sealing surface on the end of the plug is wider than other interchanges, resulting in better sealing and longer seal life. The Tru-Flate design coupler utilizes the tubular valve which supports the seal and allows more air flow at lower pressure drops than most competitive couplers. The protective collar guards against accidental disconnect.
Plews/Edelmann 18-221 Tru-Flate Air Blow Guns Plews/Edelmann 18-241 Air Blow Gun Kits Plews 41-135 Air Line Regulator with Gauge
Tru-Flate 18-221 Blow Gun
Our Price: $17.99
Combination of a blowgun and the siphon spray nozzle. Barbed siphon inlet fits 1/4 in ID hose or tubing. Use for spray, cleaning engines, applying protective coating and more. Allows full line pressure to be used. Includes 1/4 in female NPT inlet. To comply with OSHA regulations standard blowguns must be used on a regulated air line with a pressure setting not to exceed 30 psi. Interchangeable nozzles for cleaning and inflating. Complies with OSHA regulations standard blowguns must be used on a regulated air line with a pressure setting not to exceed 30 psi. Includes standard nozzle, tapered inflator nozzle and ball inflator nozzle. Compact, lightweight design with gauge, allows for easy on the tool air adjustment. Controls in-line air pressure for paint spray guns or other pneumatic tools. Helps keep airflow at exact operating pressures. Use where precise airflow is desired.
Tru-Flate 13-401 Coupler/Plug Set Tru-Flate 21-707 Safety Valve Tru-Flate 13-713 Air Line Coupler
This plug is the most easily recognized design. The long 3/4 in pilot is so distinctive it cannot be confused with any other designs. Couplers are available in sleeve type only. Tru-Flate Safety Valve, Nominal Size: 1/4 in, Operating Pressure: 125 psi, Body Material: Brass The Tru-Flate design plug is recognized by the extremely short pilot, however it has the widest metal section between the groove and the pilot. The sealing surface on the end of the plug is wider than other interchanges, resulting in better sealing and longer seal life. The Tru-Flate design coupler utilizes the tubular valve which supports the seal and allows more air flow at lower pressure drops than most competitive couplers. The protective collar guards against accidental disconnect.
COUPLER-PLUG SET 4PC          HOSE AIR 1/4INX25FT           Plews 576-50A Air Hose
Hi FLO? Couplers and Plugs increase air flow to ensure your tools will provide maximum torque and optimal performance. Push-to-connect design is made of lightweight T6 aluminum. Flexzilla? is a revolutionary hose featuring a flexible hybrid polymer material that redefines flexibility. This engineered polymer blend material permits use in environments where general purpose PVC and rubber hose may become too stiff. Flexzilla hose characteristics offer zero memory allowing it to lay flat. It won't work against you during operation and coils easily after use. Flexzilla offers extreme all weather flexibility, even in subzero conditions and is ideal in both hot and cold environments where tight radius bends are needed. Amflo? PVC air hose is ideal for general-purpose applications. It features a lightweight, flexible, kink-resistant design with bend restrictors. Its bright florescent colors reduce chances of tripping while on a jobsite.
Plews 554-50A-10 Air Hose HOSE AIR 3/8INX25FT           Bostitch BTFP72326 Mini Regulator and Gauge Kit
Amflo? PVC air hose is ideal for general-purpose applications. It features a lightweight, flexible, kink-resistant design with bend restrictors. Its bright florescent colors reduce chances of tripping while on a jobsite. Flexzilla? is a revolutionary hose featuring a flexible hybrid polymer material that redefines flexibility. This engineered polymer blend material permits use in environments where general purpose PVC and rubber hose may become too stiff. Flexzilla hose characteristics offer zero memory allowing it to lay flat. It won't work against you during operation and coils easily after use. Flexzilla offers extreme all weather flexibility, even in subzero conditions and is ideal in both hot and cold environments where tight radius bends are needed. Bostitch Regulator and Gauge Kit, Mini, Specifications: 1/4 in FNPT Connection, 15 gpm, 0 to 160 psi Pressure
HOSE AIR 1/4INX50FT           ProSource Tire Inflator Gauge HOSE AIR POLY BLUE 1/4INX25FT
Flexzilla? is a revolutionary hose featuring a flexible hybrid polymer material that redefines flexibility. This engineered polymer blend material permits use in environments where general purpose PVC and rubber hose may become too stiff. Flexzilla hose characteristics offer zero memory allowing it to lay flat. It won't work against you during operation and coils easily after use. Flexzilla offers extreme all weather flexibility, even in subzero conditions and is ideal in both hot and cold environments where tight radius bends are needed. The ProSource tire inflator has a die-cast body and dial type gauge with rubber protector and it has a fitted single clip-on connector. There is an air pressure of 0 to 220 psi and an air inlet of 1/4 in NPT. The lightweight of polyurethane hose makes it ideal for applications where dragging a heavy hose is an issue, like roofing. The smooth, non-marring finish also makes it ideal for indoor trim work where scratching surfaces could create damage. Maintains very good cold weather flexibility. Swivel end fittings reduce hose twist and bend restrictors reduce kinking and help increase the life of the hose.
HOSE AIR 3/8X50FT             Mintcraft CC910 Air Tool Accessory Kit Tru-Flate 24-343 Manual Mini Air Line Filter
Amflo Hybrid air hose is ideal for general purpose applications. The blend of materials offers the best of both worlds lighter in weight than rubber and more flexible than PVC. Its yellow color reduces chances of tripping while on a job site. The bend restrictors reduce kinking and increase the life of the hose. Vulcan Air Tool Accessory Kit, Brass/Steel, Brass/Chrome, Brass/Chrome, Includes: (1) Tapered Brass Inflator, (1) Inflation Needle, (2) 1/4 in Female Brass Plugs, (4) 1/4 in Male Brass Plugs, (1) Dual Tire Chuck, (1) Pencil Tire Gauge, (1) Brass Blow Gun, (1) Brass Safety Nozzle, (2) Male Brass Hose Connectors, (1) 1/4 in Quick Brass Coupler, (1) Air Blow Gun, (1) Female Brass Hose Connector Tru-Flate? airline filters are used for all airline applications where efficient filtration is required. Filtration removes airborne solid contaminants, pipe scale, rust, condensate and more, which may cause wear or failure of pneumatic components. Large filter element surface gives low pressure drop and long element life.
REGULATR TOOL AT-HAND INLN AIR Prohoze HOPB1450 Air Hose Tru-Flate 24-444 Mini Air Line Regulator with Pressure Gauge
The 41-145 at-hand regulator allows custom pressure settings for various tools or applications. To set required pressure, turn the regulator up to the max 140 psi and adjust downward to required pressure each time you change the pressure setting. Adjusts while in use with no need to stop working. This hybrid polymer blend air hose is designed for maximum hose life and tough jobsites. Use this bend air hose to transfer air pressure from your tank to your tool. Depend on this hybrid polymer blend air hose for safety and durability. Tru-Flate? airline regulators employ a solid piston and balanced poppet for excellent performance and longer life. The solid piston design is reliable for a broad range of demanding applications and is impervious to a wide range of lubricating oils and greases. Unlike diaphragms, the solid piston resists rupture, cracking or tearing under pressure, constant flexing or high-cycle rates. It is impervious to most chemicals, provides accurate control and assures smooth, uninterrupted operation. Tru-Flate? airline regulators have fast reverse flow capabilities, allowing installation where dual pressures are required. Feature 2 ga ports and include pressure gauge and non-rising, locking knob adjustment. Maximum pressure 250 psi primary, 2 to 125 psi secondary.
Tru-Flate 41-175 Air Compressor Accessory Kit Plews 12-50E Poly Air Hose Plews 576-100A-5 Air Hose
19-piece kit contains all accessories needed to connect and use a tank-mounted air compressor. The lightweight of polyurethane hose makes it ideal for applications where dragging a heavy hose is an issue, like roofing. The smooth, non-marring finish also makes it ideal for indoor trim work where scratching surfaces could create damage. Maintains very good cold weather flexibility. Swivel end fittings reduce hose twist and heavy-duty molded bend restrictors reduce kinking and help increase the life of the hose. Amflo? PVC air hose is ideal for general-purpose applications. It features a lightweight, flexible, kink-resistant design with bend restrictors. Its bright florescent colors reduce chances of tripping while on a jobsite.
HOSE AIR 3/8INX50FT           ProSource ATA-052-1 Hose Plug ProSource ATA-053-A Hose Plug
Flexzilla? is a revolutionary hose featuring a flexible hybrid polymer material that redefines flexibility. This engineered polymer blend material permits use in environments where general purpose PVC and rubber hose may become too stiff. Flexzilla hose characteristics offer zero memory allowing it to lay flat. It won't work against you during operation and coils easily after use. Flexzilla offers extreme all weather flexibility, even in subzero conditions and is ideal in both hot and cold environments where tight radius bends are needed. Prosource Hose Plug, Universal, Suitable for: For Air Tool and Air Compressor Hose Fitting Prosource Hose Plug, Universal, Suitable for: For Air Tool and Air Compressor Hose Fitting
Sta-Lube SL22133 Air Compressor Oil Plews 12-100E Air Hose Tru-Flate 41-907 Air Tank Conversion Kit
Helps promote longer life in all types of reciprocating and rotary compressors. Solvent refined and clay filtered for long-lasting, anti-foul operation. Cleans valve seat deposits and extends life. The lightweight of polyurethane hose makes it ideal for applications where dragging a heavy hose is an issue, like roofing. The smooth, non-marring finish also makes it ideal for indoor trim work where scratching surfaces could create damage. Maintains very good cold weather flexibility. Swivel end fittings reduce hose twist and heavy-duty molded bend restrictors reduce kinking and help increase the life of the hose. Complies with all new tank standards. Includes chuck, 4 ft air hose, pressure gauge, manifold with safety and tank valve.
Tru-Flate 24-311 Manual Air Line Filter Speedway 50180 Spray Gun Plews 13-50AE Air Hose
Tru-Flate? airline filters are used for all airline applications where efficient filtration is required. Filtration removes airborne solid contaminants, pipe scale, rust, which may cause wear or failure of pneumatic components. Large filter element surface gives low pressure drop and long element life. The mini series of airline filters offers a higher degree of filtration. All filters are complete with filter element and either manual or automatic drains. Maximum pressure 150 psi at 125 deg F with polycarbonate bowl and 250 psi at 175 deg F with metal bowl. Temperature range -10 to +175 deg F. Siphon feed type. Required pressure of 50 to 75 psi. Minimum hose diameter of 3.8 in. The lightweight of polyurethane hose makes it ideal for applications where dragging a heavy hose is an issue, like roofing. The smooth, non-marring finish also makes it ideal for indoor trim work where scratching surfaces could create damage. Maintains very good cold weather flexibility. Swivel end fittings reduce hose twist and heavy-duty molded bend restrictors reduce kinking and help increase the life of the hose.
Prohoze HOPB14100 Air Hose Abbott Rubber 1502-38X50MM Air Hose 50 ft Tru-Flate 24-414 Compact Air Line Regulator with Pressure Gauge
This hybrid polymer blend air hose is designed for maximum hose life and tough jobsites. Use this bend air hose to transfer air pressure from your tank to your tool. Depend on this hybrid polymer blend air hose for safety and durability. Rubber hose, durable, abrasion resistant. Tru-Flate? airline regulators employ a solid piston and balanced poppet for excellent performance and longer life. The solid piston design is reliable for a broad range of demanding applications and is impervious to a wide range of lubricating oils and greases. Unlike diaphragms, the solid piston resists rupture, cracking or tearing under pressure, constant flexing or high-cycle rates. It is impervious to most chemicals, provides accurate control and assures smooth, uninterrupted operation. Tru-Flate? airline regulators have fast reverse flow capabilities, allowing installation where dual pressures are required. Feature 2 ga ports and include pressure gauge and non-rising, locking knob adjustment. Maximum pressure 250 psi primary, 2 to 125 psi secondary.
Tru-Flate 24-404 Compact Air Line Regulator with Pressure Gauge HOSE AIR 1/4INX100FT          AIR HOSE PROFLEX 1/4IN X 50FT
Tru-Flate? airline regulators employ a solid piston and balanced poppet for excellent performance and longer life. The solid piston design is reliable for a broad range of demanding applications and is impervious to a wide range of lubricating oils and greases. Unlike diaphragms, the solid piston resists rupture, cracking or tearing under pressure, constant flexing or high-cycle rates. It is impervious to most chemicals, provides accurate control and assures smooth, uninterrupted operation. Tru-Flate? airline regulators have fast reverse flow capabilities, allowing installation where dual pressures are required. Feature 2 ga ports and include pressure gauge and non-rising, locking knob adjustment. Maximum pressure 250 psi primary, 2 to 125 psi secondary. Flexzilla? is a revolutionary hose featuring a flexible hybrid polymer material that redefines flexibility. This engineered polymer blend material permits use in environments where general purpose PVC and rubber hose may become too stiff. Flexzilla hose characteristics offer zero memory allowing it to lay flat. It won't work against you during operation and coils easily after use. Flexzilla offers extreme all weather flexibility, even in subzero conditions and is ideal in both hot and cold environments where tight radius bends are needed. Lightweight, reinforced polyurethane air hose. Non-marking, will not scuff painted walls. Flexible even at cold temperatures. Durable, abrasion, oil and fuel resistant. Reinforced braiding. Reusable hose guards and fittings.
Prohoze PRO-1450 Air Hose Ingersoll-Rand EC400-NS  Needle Scaler Edge 3107G Pneumatic Die Grinder
This air hose is tough and flexible. It is lightweight for easy management. Use this air hose for finish carpentry and roofing jobs. Change your air hammer into a needle scaler with a twist of the arm. It gives you the versatility you need to fly through real work. For use with the Ingersoll Rand 114GQC air hammer. The 3017G is ideal for finishing. It offers a ball-bearing construction that is sturdy yet lightweight. Features include a 1/3 hp motor, a 1/4 in collet, a rear exhaust and a self-locking throttle. An ergonomic grip makes the tool comfortable to hold and use and provides exceptional torque accuracy. Offering longer life and higher free speed at 27,000 rpm. A general-purpose tool designed for cutting, polishing, porting, light weld grinding and breaking sharp edges.
AIR HOSE PROFLEX 3/8IN X 50FT Ingersoll-Rand 114GQC Air Hammer Plews 552-50AK-5 Air Hose Kit
Lightweight, reinforced polyurethane air hose. Non-marking, will not scuff painted walls. Flexible even at cold temperatures. Durable, abrasion, oil and fuel resistant. Reinforced braiding. Reusable hose guards and fittings. This standard-duty air hammer is handy whether you're cutting panels, fixing exhaust systems or making general repairs. Powered by compressed air, this tool delivers a 2-5/8 in stroke and 3500 bpm and is equipped with a quick-change retainer that makes it easy to swap chisels. Its rugged design sports an alloyed steel barrel and a heat-treated piston. Quality rubber air hose. 300 psi. Comes with bonus blow gun kit. Use in garage, shop, industry or home. Includes safety blow gun, coupler and plugs, 5 different tips.
ProSource ATA-050 Air Hose Connector Prosource HOSE AIR 3/8INX100FT
Prosource Air Hose Connector, Suitable for: For Air Compressor Hose Fitting Portable, ready-to-use tank is great for inflating tires and cleaning engines, garage and workshop. Refills from any air service station or air compressor in minutes. Equipped with air shut-off valve, pressure gauge, regulator, 4 ft x 1/4 in air hose and tire chuck 85 to 125 psi working pressure. Convenient built-in carry handle. Flexzilla? is a revolutionary hose featuring a flexible hybrid polymer material that redefines flexibility. This engineered polymer blend material permits use in environments where general purpose PVC and rubber hose may become too stiff. Flexzilla hose characteristics offer zero memory allowing it to lay flat. It won't work against you during operation and coils easily after use. Flexzilla offers extreme all weather flexibility, even in subzero conditions and is ideal in both hot and cold environments where tight radius bends are needed.
Mintcraft TA-054 Air Hose End ProSource ATA-0243L Barb Hose Splicer ProSource ATA-057 Hose Plug
Brass fitting with 1/4 in MNPT and 3/8 in ID Dia. All brass fitting with 3/8 in MNPT. Brass fitting with 1/4 in MNPT and 1/4 in ID Dia. Use for air compressor hose fitting.
Tru-Flate 24-301 Manual Compact Air Line Filter ProSource ATA-0561 Air Line Connector Ingersoll-Rand 301B Air Angle Die Grinders
Tru-Flate? airline filters are used for all airline applications where efficient filtration is required. Filtration removes airborne solid contaminants, pipe scale, rust, condensate, etc., which may cause wear or failure of pneumatic components. Large filter element surface gives low pressure drop and long element life. The mini series of airline filters offers a higher degree of filtration. All filters are complete with filter element and either manual or automatic drains. Maximum pressure 150 psi at 125 deg F with polycarbonate bowl and 250 psi at 175 deg F with metal bowl. Temperature range -10 to +175 deg F. Prosource Air Line Connector, Suitable for: For Air Compressor Hose Fitting Whether you need a right angle configuration or a straight, compact option, the 301B and 307B die grinders will not let you down. Durable, versatile and cost effective, these grinders are great for porting, weld grinding, smoothing edges, de-burring and polishing.
Edge 3101G Pneumatic Die Grinder AIR HOSE PROFLEX 1/4IN X 100FT AIR TANK PORTABLE 10 GALLON
This powerful, 20,000 rpm die grinder is ideal for finishing. The angled shape lets you get to those hard-to-reach places with a 1/3 hp motor, a 1/4 in collet, a rear exhaust and a self-locking throttle. A grease fitting allows you to keep the gears properly lubricated. An ergonomic grip makes the tool comfortable to hold and use. Use the 3101G in various applications including cutting, porting, weld breaking, deburring, polishing and grinding. Lightweight, reinforced polyurethane air hose. Non-marking, will not scuff painted walls. Flexible even at cold temperatures. Durable, abrasion, oil and fuel resistant. Reinforced braiding. Reusable hose guards and fittings. Portable, ready-to-use tank is great for inflating tires and cleaning engines, garage and workshop. Refills from any air service station or air compressor in minutes. Equipped with air shut-off valve, pressure gauge, regulator, 4 ft x 1/4 in air hose and tire chuck 85 to 125 psi working pressure. Convenient built-in carry handle.
Abbott Rubber 1010-03825-50-4MM Quick Connect Air Hose 50 ft Prohoze PRO-14100 Air Hose Edge 311G Dual Action Pneumatic Sander
Rubber hose, durable, abrasion resistant. Rugged reinforced polyurethane construction is abrasion, puncture and chemical-resistant. Flexible from -40 to 160 degrees F for revolutionary workability. Reusable 1/4" MPT fittings are field repairable in three easy steps. Non-marring translucent material provides a clear view of airline contaminants. Hi-vis safety yellow color for improved jobsite visibility. Snap-fit strain reliefs provide flexible reinforcement for extended life. Up to 2x lighter than standard air hoses. Ribbed design prevents hose from sticking to itself or other jobsite obstructions. Dual-action air sander 6 in pad a built-in silencer muffles noise as you work with this economical dual-action sander. It's a quality sander used for feather edging, metal preparation and finish work on body filler. Its dual-action pad motion produces swirl-free finishes.
Ingersoll-Rand 170G Air Ratchet Wrenches Plews 13-100AE Air Hose Ingersoll-Rand Edge 7811G Reversible Air Drill
Ingersoll Rand's Edge Series 170G delivers the power you need to get the job done. At 55 ft-lb of maximum torque and 170 rpm free speed, this tool is the ideal fit for all of your projects. The 170G can be used in a broad range of applications where light disassembly and assembly of products is necessary. Use the 170G to access those hard-to-reach tight spaces. The lightweight of polyurethane hose makes it ideal for applications where dragging a heavy hose is an issue, like roofing. The smooth, non-marring finish also makes it ideal for indoor trim work where scratching surfaces could create damage. Maintains very good cold weather flexibility. Swivel end fittings reduce hose twist and heavy-duty molded bend restrictors reduce kinking and help increase the life of the hose. Heavy-duty reversible air drill 3/8 in chuck the Ingersoll Rand edge Series 7811G heavy-duty reversible air drill features a quiet design, with speeds from 1200 to 1700 rpm and a keyless 3/8 in chuck. Applications for this reversible air drill include home improvement projects, body work installation and repair, farm implement assembly and repair, general equipment, auto repair and maintenance and more.
Abbott Rubber 1025-0750R-50-CRS 2-Lug Air Hose 50 ft REEL AIR HOSE 3/8INX50FT      Ingersoll-Rand 210G Gravity Feed Pneumatic Spray Gun
Rubber hose, durable, abrasion resistant. From DIYers to heavy-duty professionals, the Amflo brand of automatic enclosed air hose reels has something for everyone. All reels feature impact-resistant housing, guided automatic hose rewind system and a 180 deg steel swivel mounting bracket. The ability to be mounted vertically or horizontally allows them to fit any workspace configuration. Give consumers what they need with our automatic enclosed air hose reels. Adjustable fluid, air and spray pattern controls. Works in a variety of applications, from automotive refinishing to deck and fence work. Required force is 11 cfm and operating pressure is 50 psi. Includes one nozzle (size 1.4 mm) and one 20 1/4 oz plastic paint cup.
Ingersoll-Rand EC300  Air Nibbler Ingersoll-Rand EC112  Air Drills REEL HOSE AIR 3/8IN X 50FT
The Edge 2 EC300 air nibbler offers the ability to cut up to 18 ga steel, aluminum, plastic or other metals in 6 ft per minute. Even at 4200 strokes/min the EC300 holds a tight 1/4 in radius with great accuracy giving you the control and cutting power you need all without the distorted edges. More power and control to keep you going. The Ingersoll Rand edge 2.0 EC112 air drill features a powerful and quiet design, with speeds from 500 rpm and a keyless 1/2 in chuck, its side handle and ergonomic grip make this tool more comfortable and precise when getting work done. Flexzilla? offers a variety of air hose reels to make reeling in hoses easy. Some models feature Levelwind? technology, Flexzilla's unique winding system that automatically layers hose back and forth across the reel ensuring that the hose is coiled smoothly, easily every time. All of our air hose reels enhance your work efficiency and are heavy-duty to stand up to frequent use.
Edge 300G Random Pneumatic Sander Ingersoll-Rand 107XPA Air Ratchet Wrenches Stanley-Bostitch BTFP02011 Air Compressors
COMPRESSOR AIR 6 GALLON
Our Price: $149.99
6 in Random orbital air sander this vacuum-ready, low-vibration model is lightweight yet sturdy. It produces an ultra-high-quality, swirl-free, finish and connects to central or portable vacuum systems. The 300G extracts dust and particles through the pad, keeping foreign matter away from the motor. Virtually all dust is instantly channeled away from the work. This tool is well-suited for preparing metal and wood surfaces for painting and finishing. The advanced head design of the 1077XPA 1/2 in and 107XPA 3/8 in ratchet wrenches provide increased durability to one of the industry's most popular ratchets. 6 gallon oil free Pancake compressor delivers up to 2.6 SCFM at 90 psi. Only 14" in diameter and 33 lbs. for easy portability. It's light enough to carry and get in and out of the jobsite. Long life, maintenance free pump for convenient on going uses. At just 80 dBA, this compressor offers the user a quiet work environment. Integrated control panel helps vital compressor components to be protected against tough jobsite conditions. Includes 2 Universal couplers to easily support 2 users. Ideal for trim and finish applications including installing molding, cabinetry or window/door casings.
Senco PC1010 Air Compressor Ingersoll-Rand Edge 236G Air Impact Wrench Ingersoll-Rand 231G Air Impact Wrench
The PC1010 is ultra-quiet and ultra-light lubeless pump compressor. You will find what you are looking for in the 236G 1/2 in Impactool?. With an impressive 1200 bpm and 450 ft-lb of maximum reverse torque, this tool is just what you need to get the job done. This tough Ingersoll Rand air impact wrench is great to have around the automobile shop. Its single hammer impact mechanism is durable and it boasts an easy to service two-piece construction. Maximize your productivity with the powerful 231G 1/2 in impactool?. You will be amazed by the 500 ft-lb of maximum reverse torque this tool delivers. This tough Ingersoll Rand air impact wrench is great to have around the garage, on the farm or for any task requiring quick removal of fasteners.
6GAL PANCAKE COMPRESS 150PSI  Porter-Cable C2002 Air Compressor COMPRESSOR AIR ELEC 1/2HP 1GAL
Our 150 psi 6 gal oil-free pancake compressor kit comes with the accessories you need to get to work. It features optimal stability, durable water drain valve, rubber feet and 150 psi capacity. It was designed with air tool performance in mind with 2.6 scfm at 90 psi allowing for a quick recovery time. The oil-free pump delivers maintenance-free performance. The whole unit transports easily with integrated cord wrap for convenience. It comes with a 13-piece accessory kit. Whether you're filling tires or firing a nailer, this portable compressor packs the punch you need. Our 150 psi 6 gal oil-free pancake compressor is constructed with a pancake style tank for stability, with a water drain valve and tough rubber feet. The high pressure design optimizes air tool performance, delivering 2.6 scfm at 90 psi for quick recovery time. The oil-free pump provides maintenance-free performance. Transporting is easy with the integrated cord wrap. Compressors are workhorse tools on the job site and in the work shop. Makita? air compressors are favorites for their faster recovery time, lower noise, longer tool life and consistent performance. The Makita? 1/2 hp 1 gal compact, oil-free, electric air compressor (MAC100Q) features a quiet series design, combining strong performance with lower noise. At only 58 dBA, it's ideal for indoor use during case and base installation, trim and finish carpentry, cabinet or furniture making, and more. The MAC100Q runs at a lower rpm, resulting in longer motor and pump life. It is powered by an efficient 1/2 hp induction motor that provides up to 135 psi. It also features a lightweight design (only 25.5 lb) for increased portability. The roll-cage construction provides added protection for the pump and motor assembly during transportation, in storage and on the job site. Additional features include a low amp draw that reduces the incidents of tripped breakers at start-up, as well as an oil-free dual-piston pump designed for maintenance-free operation.
Pulsar PCE6020K  Air Compressors COMPRESSOR QUITE 135PSI 1 GAL Ingersoll-Rand 2100G Composite Air Impact Wrench
This 1/3 hp 2 gal horizontal tank compressor is ideal for jobs around the house. The all steel, electro-statically painted tank is designed for years of use while the sealed lubrication system means you never have to worry about adding oil. Ideal for inflating tires or toys with the included six piece accessory kit and even used with low draw tools like nailer or staplers the PCE6021K has 100 psi maximum pressure while providing 1.5 cfm at 40 psi and 0.7 cfm at 90 psi. 0.75 scfm delivered at 90 psi, 1 gal tank and 135 maximum psi enables more nails to be fired and provides quicker recovery. Durable oil-free pump provides extended maintenance-free operation. Low 2.6 A draw motor provides easy start-up and reduces breaker tripping. Belt drive. Low 71 dBA allows for quieter operation. Roll cage and control panel provide protection to key compressor components. Lightweight at only 24 lb, thin (9 in) and compact design is easy to carry and store. Ball valve drain allows for quick and thorough tank draining. One quick coupler to easily support one nailer. Convenient cord wrap for easy storage. High-flow regulator for increased performance. With a great power to weight ratio the 2100G makes it comfortable to get the job done. Delivering 550 ft-lb of maximum reverse torque and weighing only 4.3 lb, this tool has what it takes to handle the toughest jobs. This powerful, lightweight Ingersoll Rand composite air impact wrench delivers high torque through a sophisticated power management system.
Ingersoll-Rand 231C Air Impact Wrench Ingersoll-Rand 1077XPA Air Ratchet Wrenches ProSource ATA-055 Quick Coupler
The heavy-duty 231C impact wrench has the reliability and durability you have come to expect from the Ingersoll Rand name. The powerful tool provides an even impact and is durable enough to last through the toughest work environments. The advanced head design of the 1077XPA 1/2 in and 107XPA 3/8 in ratchet wrenches provide increased durability to one of the industry's most popular ratchets. Prosource Quick Coupler, Universal, Suitable for: For Air Tool and Air Compressor Hose Fitting
Senco PC1010N  Air Compressors COMPRESOR PANCAKE 165 PSI 6GAL Ingersoll-Rand EB2125X Air Impact Wrench
SENCO's 1 gal finish and trim air compressor is designed with the professional contractor in mind. The lightweight and compact design ensure easy portability combined with the ultra-quiet operation makes this the ideal finish and D6 trim unit. The long life induction motor and oil-free pump design eliminate the need for oil or regular maintenance. 165 maximum psi tank (22.7 L) and 2.6 scfm delivered at 90 psi pump, enable long tool run time with quick recovery. High-efficiency motor for easy start up in cold weather or extension cord application. (14 ga or larger, 50 ft (15.2 m) or less). 75.5 dBA noise level for a quiet work environment. High flow regulator and couplers to maximize air tool performance. Long life oil-free pump for maintenance-free operation. Console cover protects controls and is removable to allow easy repair. Outlet tube re-routed to avoid being catch point. 30 lb weight makes unit easy to carry/store. Two universal couplers to easily support two users. Ball drain valve for quick and thorough tank draining. Convenient cord wrap for easy storage. Protective rubber leg covers to prevent marring. High flow regulator for increased performance. 120 V, 60 Hz, 10 A universal motor. The first impact wrench from our EDGE 2 lineup is also the most powerful impact in our whole EDGE Series portfolio. 690 ft-lb of reverse torque means you will have the power you need to bust trough those stubborn bolts.
Ingersoll-Rand 212 General Duty Air Impact Wrench Plews 545HR-RET Reel Air Hose ProSource ATA-056 Quick Coupler
Whether you are working on vehicle repair or maintenance repair, the 212 impact wrench will help you through even the toughest of jobs. Amflo? Manual hose reels feature all-steel construction, comfortable handle grips and a spring tension brake to prevent accidental unwinding. Standard manual reels can be mounted horizontally or vertically and are available in three configurations assembled with hose and assembled or unassembled without hose to take up less space on the retail shelf. The dual output manual reel sits on the ground or can be conveniently nailed to the roof for maximum maneuverability. It is ideal for the construction site as it comes with 75 ft of lightweight polyurethane air hose. Manual hose reels are ideal for the economical shopper in the market for an air hose reel. Prosource Quick Coupler, Universal, Suitable for: For Air Tool and Air Compressor Hose Fitting
Hitachi EC12 Portable Air Compressor COMPRESSOR AIR ELE1-1/2HP 3GAL Pulsar PCE6060K Air Compressors
The EC99S twin stack compressor features an oil-lubricated cast iron pump and 15 A direct drive induction motor for longer life. The motor is protected by a thermal overload protection that stops the motor in a possible overheating situation. Weighing just 52.9 lb, the EC99S has an ergonomic carrying handle to make it easier to transport to any jobsite. A universal quick coupler and steel encased industrial gauges are factory installed on the unit so it is ready to go out of the box. Compressors are workhorse tools on the job site and in the work shop. Makita? air compressors are favorites for their faster recovery time, lower noise, longer tool life and consistent performance. The Makita? quiet series 1-1/2 hp, 3 gal, oil-free, electric air compressor (MAC320Q) features a quiet series design, combining strong performance with lower noise. At only 60 dBA, it's ideal for indoor use during case and base installation, trim and finish carpentry, cabinet or furniture making, and more. The MAC320Q runs at a lower rpm, resulting in longer motor and pump life. It is powered by an efficient 1-1/2 hp induction motor that provides up to 90 psi. It also features a lightweight design (only 52.5 lb) for increased portability. This enduring compressor design has been the favorite of millions throughout the years. With a six gallon tank capacity that has been electro statically painted for years of use, powerful 3.5 hp electric motor, oil reservoir creates 115 psi and has output levels of 5.2 cfm at 40 psi and 4.2 cfm at 90 psi, allowing it to operate many air tool for extended periods of time without the worry of recycle time. The PCE6060K incorporates dual pressure gauges and brass quick connect couplers meaning that changing tools is a breeze, even in the middle of a job, while the handy handle and mobility kit allow the job to be almost anywhere there is electricity available.
Senco PC1280  Air Compressors COMPRESSOR .75HP 125PSI HOTDOG COMPRESSOR AIR 1HP 1.5GAL
SENCO's 6 gal pancake air compressor is designed with the power and speed to handle all finish and trim applications. The compact, lightweight and balanced design allows for easy portability. The oil-free pump allows for maintenance-free operation. 1 cfm at 100 psi. Maximum pressure of 125 psi. Power rating of 0.75 Peak hp. 1 gal air tank capacity. Dimension of 14.1 in L x 13.77 in W x 12.6 in H. Weighs 24.7 lb. IRON HORSE Air Compressor, 1 hp, Tank Capacity: 1 gal
Ingersoll-Rand Edge Pro 2317G Air Impact Wrench Kit Ingersoll-Rand 2115TIMAX Industrial Duty Air Impact Wrench Senco PC0968 Air Compressor
This set includes a 231G air impact wrench and a 170G air ratchet wrench along with a five-piece socket set. The impact wrench's 6-vane motor yields an optimal power to weight ratio, while the ratchet wrench's motor delivers 55 foot pounds of torque and 170 rpm of free speed. Both tools sport an ergonomic design for greater comfort. A blow molded storage case makes carrying the set easy. Made with durable materials and featuring a number of different anvil configurations, this 2115TiMAX Series are a tools you can count on. Designed with the power and speed to handle all finish and trim applications. The PC0968 comes with an oil-less pump and weighing in at only 38 lb this compressor will not wear you down.
ThunderGun 232TGSL Air Impact Wrench HOSE AIR BULK 1/4INX250FT     COMPRESSOR CRDLS 60V 2.5GAL
As close as you can get to the real racing tools used by Nascar pit crews. It features 625 ft-lb of torque in reverse, with 10,000 rpm to deliver pit crew power, speed and durability for shop tasks. The Flexzilla? Pro Custom Hose Center allows you to provide your customers with custom length hose assemblies. Using Flexzilla Pro Reusable Ends, you can quickly and easily create custom length hose assemblies on site. The 60 V MAX FLEXVOLT 2.5 gal Cordless Air Compressor offers all of the convenience and portability of cordless and lets you continue using the pneumatic tools you already have. Each battery charge allows for up to 1220 nails, providing the runtime to complete a variety of applications. Its OneTurn? regulator means you no longer have to fight with the dial. Plus, it's made right here in the USA with global materials.
COMPRESSOR HANDCARRY 100PSI 4G COMPRESSOR AIR 2.5 HP         COMPRESSOR HD 200 PSI 2-1/2GAL
DeWALT Electric Hand Carry Compressor, 120 VAC, 2.0 hp, 15 A, Frequency Rating: 60 Hz, Number of Phases: 1, Number of Stages: 1, Tank Type: Twin Stack, Tank Capacity: 4 gal, 125 psi, Air Flow Rate: 4 cfm, 3400 rpm, Sound Level: 78.5 dB, Motor Type: Induction, Pump Type: Oil-Lubricated, Drive Type: Direct, Iron, Dimensions: 18 in L x 18-1/2 in W x 16-3/4 in H, Includes: DeWALT Compressor Oil Makita's 2.5 hp air compressor is equipped with Makita's Big Bore? engineered pump cylinder and piston for higher output for two nailers, with less noise and improved job site performance. The MAC2400 delivers industrial power and results with improved durability for tough job site conditions. The MAC2400 is powered by a 2.5 hp motor. The Makita Big Bore? engineered pump with cast iron cylinder has greater bore and stroke for increased compression, faster recovery and less noise. The cast iron construction is engineered for increased durability even under tough job site conditions. The MAC2400 has an oil lubricated pump and is equipped with a large automotive style filter for increased air intake and greater efficiency. The Big Bore? oil-lubricated pump is also more efficient and the MAC2400 runs cooler and at half the rpm of most competitive units, resulting in greater motor and pump life and lower noise. The 4.2 gal twin-stacked tank sustains an operating pressure of 130 psi and delivers 40 psi (4.8 cfm) and 90 psi (4.2 cfm), enough for two nailers. The low AMP draw reduces instances of tripped breakers and voltage drop that can cause premature motor failure. The roll bar handle provides portability and additional protection, helping it withstand harsh jobsite environments. Additional features include a convenient oil drain and oil sight glass, a tank drain valve that supersedes standard petcock design for easier maintenance and finned discharge tubing that dissipates heat more efficiently. The MAC2400 is engineered for low noise, high output and less maintenance and delivers industrial power and results with improved durability under tough job site conditions. 3 scfm delivered at 90 psi pump. 2.5 gal tank and 200 maximum psi enables a large amount of nails to be fired and provides quick recovery. Durable oil-free pump provides extended maintenance-free operation. Low 71.5 dBA allows for quieter operation (tested per ISO3744). Low 12 A draw motor provides easy start-up and reduces breaker tripping. Lightweight (36 lb), thin (12-1/2 in) and compact design is easy to carry and store. Compressor can be operated/stored in either the vertical or horizontal position. Roll cage and control panel provide protection to key compressor components. Dual quick couplers to easily support two nailers. Ball valve drain allows for quick and thorough tank draining. Convenient cord wrap for easy storage. High-flow regulator for increased performance. Drive belt. 120 V, 60 Hz and 8 A universal motor. Pump speed of 2300 rpm.
COMPRESSOR CMPCT M18 FUEL 2GAL Ingersoll-Rand 3445MAX Pneumatic Angle Grinder Stanley CAP2040ST-OL Air Compressor
Our M18 FUEL? 2 gal compact quiet compressor is designed for the professional carpenter and remodeler. This quiet air compressor is only 68 dBA, making it the quietest cordless compressor on the market and quieter than most corded options. We've designed this 2 gal air compressor to be high performing while reducing the noise professionals deal with on jobsites. Its low profile and stackable design allow our portable air compressor to be easily stored and transported on, around and back off the jobsite. It has run time professionals need to stay productive, giving you up to 1600 18 ga brad nails per charge. It is compatible with all Milwaukee? M18? REDLITHIUM? batteries making it easy to swap packs and keep running to finish your job. MAX Series air angle grinder the 3445MAX is the ideal choice for high-performance material removal. This 4-1/2 in air angle grinder combines a unique internal governor with a powerful 0.88 hp motor, to give you a best-in-class power to weight ratio grinder that will maximize your rate of material removal. Compact design was engineered to be more maneuverable and convenient to carry. It offers enough air flow to operate two framing nailers or three roofing nailers simultaneously. Four oversized rubber feet to help minimize vibration. Durable ball type drain valve. Roll bar handle protects the oil site glass and other gauges against damage if the unit accidentally tips or rolls over. Upgraded industrial-grade pressure switch/regulator makes for easy adjustments and increased durability. Oil-lubricated pump offers a cast iron cylinder for durable performance over extended periods of use.  Specs: 3 horsepower (peak) induction motor, this unit draws only 13.8 amps (120 volts) to prevent circuit breakers from flipping as the motor cuts in and out. Four-gallon stack tank compressor providing 4 CFM at 90 psi and a maximum operating pressure of 135 psi.
Senco PC1131 Air Compressor Pulsar PCE6050T Air Compressors Pulsar PCE6150 Air Compressors
SENCO's PC1131 workhorse compressor generates 4.4 cfm which provides power for all types of applications, from finish to framing. The oil splash design and induction motor provides the durability expected for professional contractors. The twin tank design of this oil-lubricated, 5 gal unit results in the smallest footprint of any compressor design. Add a powerful 3.5 hp electric motor, flutter-valve pump that puts out 115 psi and cfm's of 5.2 at 40 psi and 4.2 at 90 psi and you have a compact compressor capable of use with all but the most demanding air tools. Functional enough for use as an inflator, yet vibrant enough for use with the majority of air tools, the PCE6050T includes dual pressure gauges and dual quick couplers. When air capacity is an issue and jobs are long, the PCE6150 answers the bell with its 15 gal electro-statically painted tank married to a powerful 3.5 hp high capacity electric motor the creates 115 psi to ensure optimum torque while producing 5.2 cfm at 450 psi and 4.2 cfm at 90 to ensure duration. Add dual pressure gauges and quick couplers that allow the user to incorporate two tools at one time and it is easy to see why this unit can be used day in and day out to get the job done.
COMPRESSOR AIR 3.0 HP         WRENCH IMPACT 1/2IN 930FT/LBS Ingersoll-Rand P1IU-A9 Air Compressor
Makita's 3 hp air compressor is equipped with Makita's Big Bore? engineered pump cylinder and piston for higher output for two nailers, with less noise and improved jobsite performance. The MAC5200 delivers industrial power and results with improved durability and includes rugged wheels and folding handle for easy transport. The MAC5200 is powered by a 3 hp motor with built-in thermal overload for additional protection. The Makita Big Bore? engineered pump with cast iron cylinder has greater bore and stroke for increased compression, faster recovery and less noise. The cast iron construction is engineered for increased durability even under tough job site conditions. The MAC5200 has an oil-lubricated pump and is equipped with a large automotive style filter for increased air intake and greater efficiency. The 5.2 gal tank sustains an operating pressure of 140 psi and delivers 40 psi (6.9 cfm) and 90 psi (6.5 cfm), enough for two nailers. The oil-lubricated pump runs cooler and the finned discharge tubing dissipates heat more efficiently. The roll cage construction is built for extra protection for the pump and motor assembly, helping it withstand harsh jobsite environments. Ease-of-use and convenience features include tool hangers, a built-in storage compartment for air fittings and accessories and an air hose wrap to store 50 ft of 3/8 in air hose with handle folded or upright. Other features include a convenient oil drain and oil sight glass and a tank drain valve that supersedes standard petcock design for easier maintenance. The powerful 2235TiMAX Series impact wrench is lightweight, durable and versatile. It will withstand anything you throw at it and still deliver the same quality output every time. The Ingersoll Rand oil-lubricated twin-stack reciprocating air compressor is designed to provide power, durability and portability on the jobsite or for DIY projects. From interior trim and finish to roofing and decking, the twin-stack can do the job. Built to last, the compressor features a durable cast-iron cylinder designed for the toughest 100% continuous-duty applications. The twin-stack compressor package comes standard with two 1/4 in universal couplers, front panel-mounted regulator and pressure gauge, 4 gal twin tanks, all season select lubricant and a power cord.
COMPRESSOR WHEEL 200PSI 4-1/2G HOSE AIR BULK 3/8INX250FT     COMPRESSOR WORKSHOP 200PSI 15G
200 psi maximum tank storage pressure provides a user with 80% more usable air. 5 scfm at 90 psi allows the compressor to recover quickly after its initial tank charge is exhausted. Vertical stand feature and collapsible handle allows a user to save space by transporting or storing the compressor in a vertical position. 78 dBA operation noise level for a quieter work environment. 10 in non-flat foam tires allow for easy transportation around the jobsite. EHP efficient high pressure technology allows for longer pump and motor life. Oil-free, maintenance-free pump for convenient use. Efficient high pressure motor allows the compressor to be run with an extension cord (12 ga or heavier, 50 ft or less) due to consistent amp draw requirement of the compressor. High flow coupler allows for maximum nailer performance. Metal console panel provides a display area as well as protects the gauges, couplers and regulator. High flow coupler allows for maximum nailer performance. 2 in gauges allow for an easy-to-read surface. Weighs 83 lb. The Flexzilla? Pro custom hose center allows you to provide your customers with custom-length hose assemblies. Using Flexzilla? Pro reusable ends, you can quickly and easily create custom length hose assemblies on site. 5.0 SCFM at 90 psi allows for quick compressor recovery times. 200 psi max tank storage pressure allows for longer air tool run times. 78 dBA (tested per ISO3744) operational noise level for a quieter work environment. EHP efficient high pressure technology delivers exceptional air-tool run times. Oil free, maintenance free pump for convenient use. Efficient high pressure motor allows the compressor to be run with an extension cord (12 ga. or heavier, 50 ft or less) due to consistent amp draw requirements of the compressor. Compact design allows for the compressor to be easily moved, transported and stored. Robust dual purpose handle provides additional protection to the compressor along with serving as a hose wrap. Metal console panel protects the gauge, coupler and regulator. High flow air regulator and high flow coupler allows for maximum air tool run time. 2 inch gauges allow for an easy to read surface. Wide track, semi-pneumatic tires allow for additional stability, easy movement and no tire maintenance. 1,750 rpm pump speed. 120 volts power supply.
Pulsar PCE6280 Air Compressors COMPRESSOR 1.5HP 125PSI STACK HOSE AIR BULK 1/2INX250FT
This full size single stage, 28 gal compressor is designed for the serious user of air tools. With a pro-grade 5. hp motor and deep well oil lube pump, the PCE6280 can perform for hours on end and work with virtually any air tool in the tool box. Producing 115 psi maximum pressure and cfm of 6.2 at 40 and 5.2 at 90, the produced air flow and torque will mean that few jobs will be left undone. Add an electro-statically painted tank surface, dual pressure gauges and a brass quick-coupler along with both a compact handle and roll about wheels and one can quickly see why the PCE6280 is a contender for inclusion in any serious handyman's tool arsenal. "2.5 CFM at 90 psi. 1.5 (Peak) horsepower. 125 psi max. 47 dB @25 ft. 4 gallon air tank capacity. Dimensions: 16.93""L x 16.54""W x 16.54""H. Weighs 68.5 lbs." The Flexzilla? Pro custom hose center allows you to provide your customers with custom-length hose assemblies. Using Flexzilla? Pro reusable ends, you can quickly and easily create custom length hose assemblies on site.
Ingersoll-Rand 261 Air Impact Wrench Ingersoll-Rand 2145QIMAX Air Impact Wrench Ingersoll-Rand 285B-6 General Duty Air Impact Wrench
The 261 Series impact wrench is ideal for vehicle repair and heavy truck and machinery jobs where you will benefit from the square socket retaining ring and the power behind the vane motor. Trigger actuation and a power regulator let you complete projects with control and ease. The Ingersoll Rand 2155QiMAX 1 in Impactool? delivers incredible performance and industrial-grade durability in an impact wrench. Plus, its efficient air motor reduces air consumption to save you money. Ideal for the most demanding applications. The 285B Series impact wrench is great for any garage. Fitted with an extended anvil, changing tires and deeper fastening will be a breeze.
Ingersoll-Rand P1.5IU-A9 Air Compressor COMPRESSOR 2HP 125PSI S-STACK Hitachi EC2510E Air Compressor
Designed for professionals and serious do-it-yourselfers, the versatile garage mate is ideal for the home, shop or jobsite. Delivering maximum air, the garage mate can power impact guns, ratchets, grinders, drills, nailers, paint sprayers, sanders and more. The garage mate features a cast-iron, oil-lubricated pump for solid, reliable performance. Belt-driven for quiet operation (75 to 80 dBA), all models are equipped with a pressure switch, pressure gauge, regulator, safety valve, manual drain and 6 ft power cord. "5.0 CFM at 90 psi. 125 max psi. 2.0 (Peak) horsepower. 49 dB @25 ft. 5 gallon air tank capacity. Dimensions: 28.35""L x 20.08""W x 20.08""H. Weighs 86.3 lbs." The EC2510E 8 gal gas powered wheeled air compressor combines contractor-grade quality with simplified operation. Designed to work day-in and day-out, this compressor provides plenty of air and cycles from 116 psi to a maximum of 145 psi so it turns on well before tools requirements are compromised.
Ingersoll-Rand SS3J5.5GH-WB Air Compressor IronHorse IHD6160V1 Air Compressor Woods/Iron Horse IHD7180V1 Iron Horse Air Compressors
Ingersoll Rand gas engine wheelbarrow air compressors are lightweight with a low-profile design providing maximum maneuverability on the jobsite. Built to last, these cast-iron, oil-lube compressors are designed for the toughest 100% continuous duty applications. The wheelbarrow compressor package includes pressure switch, regulator and gauge, two quick disconnects to power multiple tools and twin 8 gal capacity tanks. These gas-driven models are powered by an easy-starting 5.5 hp Honda or Kohler high-performance engine. Thermally protected  electric motor with 60 gallon ASME registered tank, easy view oil sight gauge, cast iron compressor  minimizes vibration. Individual and removable cylinders, no magnetic motor starter required, pressure switch has on/off control. High efficiency reed valves for maximum performance, efficient heat removal from pulley-fan, sturdy belt guard. Specs: CFM/PSI is 11.2 CFM at 90 PSI, max rated PSI is 150, 208/230V electric motor, dimensions are: 27"Lx20"Wx65"H, weighs 260 lbs. Features a 3-piston "V" style cast iron pump for longer life. Produces 16.5 cfm at 90 psi with a max pressure of 150 psi. No magnetic starter required. Oil sight glass. Enclosed belt guard. Heavy-duty pressure switch. ASME certified tank that meets the national pressure vessel certifications.
   
 
1