Home > HARDWARE > CONSTRUCTION HARDWARE > JOIST HANGERS & CONNECTORS > JOIST HANGERS
Sort By:
1
JOIST HANGER LIGHT ZMAX 2X4IN JOIST HANGER HEAVY ZMAX 4X6IN JOIST HANGER ZMAX 18GA 2X6IN
APLH light hangers connect 2X joists to beams. These concealed-flange hangers feature straight edges and provide a cleaner looking installation for joist connections. Available in a range of sizes, the hangers install easily with the Outdoor Accents? connector screw. APHH heavy hangers connect 4X and 6X beams to girders. These concealed-flange hangers feature straight edges and provide a cleaner looking installation for joist connections. Available in a range of sizes, the hangers install easily to the joist with the Outdoor Accents? structural wood screw and hex head washer and to the header with the Strong-Drive? SDS heavy-duty connector screw. The LUC is designed to provide support underneath the joist, rafter or beam to provide a strong connection. This face-mount hanger has concealed header flanges that make for cleaner visible lines in exposed conditions. The LUC is value-engineered for strength and economy and provides for easier and faster installation.
JOIST HANGER GALV 20GA 2X10IN JOIST HANGER GALV 18GA 2 X 6IN JOIST HANGER LIGHT ZMAX 2X6IN
The LU is designed for joist-to-header installation in wood-framed construction. This face-mount hanger features speed prongs to temporarily position and secure the connector for easier and faster installation. The economical LU hanger is value-engineered for strength. The LUS is an easy to install, economical hanger designed for common lumber sizes. This widely used hanger features double-shear nailing that distributes the load through two points on each joist nail for greater strength. This allows for fewer nails, faster installation and the use of all common nails for the same connection. APLH light hangers connect 2X joists to beams. These concealed-flange hangers feature straight edges and provide a cleaner looking installation for joist connections. Available in a range of sizes, the hangers install easily with the Outdoor Accents? connector screw.
JOIST HANGER GALV 20GA 2 X 4IN JOIST HANGER ZMAX 18GA 2X10IN JOIST HANGER GALV 18GA 2X10IN
The LU is designed for joist-to-header installation in wood-framed construction. This face-mount hanger features speed prongs to temporarily position and secure the connector for easier and faster installation. The economical LU hanger is value-engineered for strength. The LUC is designed to provide support underneath the joist, rafter or beam to provide a strong connection. This face-mount hanger has concealed header flanges that make for cleaner visible lines in exposed conditions. The LUC is value-engineered for strength and economy and provides for easier and faster installation. The LUS is an easy to install, economical hanger designed for common lumber sizes. This widely used hanger features double-shear nailing that distributes the load through two points on each joist nail for greater strength. This allows for fewer nails, faster installation and the use of all common nails for the same connection.
JOIST HANGER GALV 18GA 2 X 4IN JOIST HANGER GALV 18GA 2 X 8IN JOIST HANGER GALV 20GA 2 X 6IN
The LUS is an easy to install, economical hanger designed for common lumber sizes. This widely used hanger features double-shear nailing that distributes the load through two points on each joist nail for greater strength. This allows for fewer nails, faster installation and the use of all common nails for the same connection. The LUS is an easy to install, economical hanger designed for common lumber sizes. This widely used hanger features double-shear nailing that distributes the load through two points on each joist nail for greater strength. This allows for fewer nails, faster installation and the use of all common nails for the same connection. The LU is designed for joist-to-header installation in wood-framed construction. This face-mount hanger features speed prongs to temporarily position and secure the connector for easier and faster installation. The economical LU hanger is value-engineered for strength.
JOIST HANGER ZMAX 18GA 2 X 4IN JOIST HANGER ZMAX 18GA 2 X 6IN JOIST HANGER GALV 18GA 2X10IN
The LUS is an easy to install, economical hanger designed for common lumber sizes. This widely used hanger features double-shear nailing that distributes the load through two points on each joist nail for greater strength. This allows for fewer nails, faster installation and the use of all common nails for the same connection. The LUS is an easy to install, economical hanger designed for common lumber sizes. This widely used hanger features double-shear nailing that distributes the load through two points on each joist nail for greater strength. This allows for fewer nails, faster installation and the use of all common nails for the same connection. The LUS is an easy to install, economical hanger designed for common lumber sizes. This widely used hanger features double-shear nailing that distributes the load through two points on each joist nail for greater strength. This allows for fewer nails, faster installation and the use of all common nails for the same connection.
JOIST HANGER GALV 20GA 2 X 8IN DECK TENSION TIE ZMAX 14GA    LEFT-SKEWED U-HANGER ZMAX 2X6
The LU is designed for joist-to-header installation in wood-framed construction. This face-mount hanger features speed prongs to temporarily position and secure the connector for easier and faster installation. The economical LU hanger is value-engineered for strength. DTT tension ties are safe, cost-effective connectors designed to meet or exceed code requirements for deck construction. These versatile DTT connectors are also load-rated as a hold-down for light-duty shearwalls and braced-wall panel applications. The SUR/L are 45 deg skewed hangers designed to support solid sawn and engineered-wood products used in wood construction. These U-shaped hangers encapsulate the top-flange of the joist, so no web stiffeners are required for standard installation.
RIGHT-SKEWED U-HANGER ZMAX 2X6 I-JOIST HANGER 2-5/16X11-7/8IN JOIST HANGER ZMAX 18GA 2X10IN
The SUR/L are 45 deg skewed hangers designed to support solid sawn and engineered-wood products used in wood construction. These U-shaped hangers encapsulate the top-flange of the joist, so no web stiffeners are required for standard installation. The IUS is a hybrid hanger that incorporates the advantages of the face-mount and top-mount hanger. The Strong-Grip? seat feature allows the I-joist to snap securely into place without the need for joist nails, resulting in a low installed cost. The IUS hanger also features easy-to-reach face nails and self-jigging locator tabs for easier installation. The LUS is an easy to install, economical hanger designed for common lumber sizes. This widely used hanger features double-shear nailing that distributes the load through two points on each joist nail for greater strength. This allows for fewer nails, faster installation and the use of all common nails for the same connection.
JOIST HANGER GALV 18GA 2 X 6IN JOIST HANGER GALV 18GA 2 X 8IN JOIST HANGER ZMAX 18GA 2 X 8IN
The LUS is an easy to install, economical hanger designed for common lumber sizes. This widely used hanger features double-shear nailing that distributes the load through two points on each joist nail for greater strength. This allows for fewer nails, faster installation and the use of all common nails for the same connection. The LUS is an easy to install, economical hanger designed for common lumber sizes. This widely used hanger features double-shear nailing that distributes the load through two points on each joist nail for greater strength. This allows for fewer nails, faster installation and the use of all common nails for the same connection. The LUS is an easy to install, economical hanger designed for common lumber sizes. This widely used hanger features double-shear nailing that distributes the load through two points on each joist nail for greater strength. This allows for fewer nails, faster installation and the use of all common nails for the same connection.
PST-FRAME HANGER GALV 20GA 2X6 I-JOIST HANGER 1-3/4X11-7/8IN PST-FRAME HANGER GALV 20GA 2X4
The PFDB is a top-flange saddle hanger designed for post-frame construction. It has dome-shaped joist nail holes that guide nails into the proper installation angle. The PFDB features a folded seat that raises the 2X joist slightly above the seat radius to enable a tighter connection to the back of the hanger. The solid, one-piece top-flange allows for accurate and fast installation. The IUS is a hybrid hanger that incorporates the advantages of the face-mount and top-mount hanger. The Strong-Grip? seat feature allows the I-joist to snap securely into place without the need for joist nails, resulting in a low installed cost. The IUS hanger also features easy-to-reach face nails and self-jigging locator tabs for easier installation. The PFDB is a top-flange saddle hanger designed for post-frame construction. It has dome-shaped joist nail holes that guide nails into the proper installation angle. The PFDB features a folded seat that raises the 2X joist slightly above the seat radius to enable a tighter connection to the back of the hanger. The solid, one-piece top flange allows for accurate and fast installation.
PST-FRAME HANGER GALV 20GA 2X4 I-JOIST HANGER 2-1/2X11-7/8IN RAFTER HANGER ZMAX 18GA 2X6IN
The PFB top-flange hanger is for use in post-frame construction. It has dome-shaped joist nail holes that guide nails into the proper installation angle. The PFB features a folded seat that raises the 2X joist slightly above the seat radius to enable a tighter connection to the back of the hanger. The IUS is a hybrid hanger that incorporates the advantages of the face-mount and top-mount hanger. The Strong-Grip? seat feature allows the I-joist to snap securely into place without the need for joist nails, resulting in a low installed cost. The IUS hanger also features easy-to-reach face nails and self-jigging locator tabs for easier installation. The LRUZ offers an economic alternative for those applications requiring a sloped hanger for rafter-to ridge connections. Used with solid sawn rafters, the LRUZ's unique design enables the hanger to be installed either before or after the rafter is in place. The field-adjustable seat helps improve job efficiency by eliminating mismatched angles in the field and lead times associated with special orders. The LRUZ offers comparable or better load capacity to other rafter hangers at a reduced cost while using fewer fasteners.
JOIST HANGER ZMAX 18GA 2X10IN JOIST HANGER ZMAX 18GA 2 X 8IN TRUSS HANGER ADJ ZN GALV 2X9IN
The LUS is an easy to install, economical hanger designed for common lumber sizes. This widely used hanger features double-shear nailing that distributes the load through two points on each joist nail for greater strength. This allows for fewer nails, faster installation and the use of all common nails for the same connection. The LUS is an easy to install, economical hanger designed for common lumber sizes. This widely used hanger features double-shear nailing that distributes the load through two points on each joist nail for greater strength. This allows for fewer nails, faster installation and the use of all common nails for the same connection. The THA is a wood connector designed to support trusses and beams. This versatile U-shaped truss hanger features long, straight straps for applications where the height location of the truss needs to be adjustable. The field-adjustable THA can be used for top-flange or face-mount installation.
U-HANGER DBL SHR GALV 16GA 2X8 I-JOIST HANGER GALV 2X11-7/8IN JOIST HANGER ZMAX 18GA 2 X 8IN
The HUS is designed for applications where higher loads are needed. This hanger features double-shear nailing that distributes the load through two points on each joist nail for greater strength. This feature allows for fewer nails, faster installation and the use of all common nails for the same connection. The IUS is a hybrid hanger that incorporates the advantages of the face-mount and top-mount hanger. The Strong-Grip? seat feature allows the I-joist to snap securely into place without the need for joist nails, resulting in a low installed cost. The IUS hanger also features easy-to-reach face nails and self-jigging locator tabs for easier installation. The LUS is an easy to install, economical hanger designed for common lumber sizes. This widely used hanger features double-shear nailing that distributes the load through two points on each joist nail for greater strength. This allows for fewer nails, faster installation and the use of all common nails for the same connection.
TOP-FLG HANGER 18GA 2X11-7/8IN JOIST HANGER ZMAX 18GA 2 X 6IN LEFT-SKEWED U-HANGER ZMAX 2X10
The innovative ITS is designed to support 90 deg connections of I-joists to headers. This top-flange hanger features the Strong-Grip? seat and Funnel Flange? design allowing standard joist installation without the use of joist nails, resulting in the lowest installed cost. The LUS is an easy to install, economical hanger designed for common lumber sizes. This widely used hanger features double-shear nailing that distributes the load through two points on each joist nail for greater strength. This allows for fewer nails, faster installation and the use of all common nails for the same connection. The SUR/L are 45 deg skewed hangers designed to support solid sawn and engineered-wood products used in wood construction. These U-shaped hangers encapsulate the top-flange of the joist, so no web stiffeners are required for standard installation.
I-JOIST HANGER GALV 2-1/2X14IN RIGHT-SKEWD U-HANGER ZMAX 2X10 TOP-FLG HANGER 2-1/2X11-7/8IN
The IUS is a hybrid hanger that incorporates the advantages of the face-mount and top-mount hanger. The Strong-Grip? seat feature allows the I-joist to snap securely into place without the need for joist nails, resulting in a low installed cost. The IUS hanger also features easy-to-reach face nails and self-jigging locator tabs for easier installation. The SUR/L are 45 deg skewed hangers designed to support solid sawn and engineered-wood products used in wood construction. These U-shaped hangers encapsulate the top-flange of the joist, so no web stiffeners are required for standard installation. The innovative ITS is designed to support 90 deg connections of I-joists to headers. This top-flange hanger features the Strong-Grip? seat and Funnel Flange? design allowing standard joist installation without the use of joist nails, resulting in the lowest installed cost.
I-JOIST HANGER GALV 2-5/16X14 PST-FRAME HANGER GALV 20GA 2X6 DECK TENSION TIE ZMAX 14GA
The IUS is a hybrid hanger that incorporates the advantages of the face-mount and top-mount hanger. The Strong-Grip? seat feature allows the I-joist to snap securely into place without the need for joist nails, resulting in a low installed cost. The IUS hanger also features easy-to-reach face nails and self-jigging locator tabs for easier installation. The PFB top-flange hanger is for use in post-frame construction. It has dome-shaped joist nail holes that guide nails into the proper installation angle. The PFB features a folded seat that raises the 2X joist slightly above the seat radius to enable a tighter connection to the back of the hanger. DTT tension ties are safe, cost-effective connectors designed to meet or exceed code requirements for deck construction. These versatile DTT connectors are also load-rated as a hold-down for light-duty shearwalls and braced-wall panel applications.
JOIST HANGER ZMAX 18GA 2X10IN TRUSS HANGER GALV 16GA 2 X 6IN RAFTER HANGER ZMAX 18GA 2X10IN
The LUS is an easy to install, economical hanger designed for common lumber sizes. This widely used hanger features double-shear nailing that distributes the load through two points on each joist nail for greater strength. This allows for fewer nails, faster installation and the use of all common nails for the same connection. The HTU face-mount truss hanger has nail patterns designed specifically for shallow heel heights, so that full allowable loads apply to heel heights as low as 3-7/8 in. Minimum and maximum nailing options provide solutions for varying heel heights and end conditions. Alternate allowable loads are provided for gaps between the end of the truss and the carrying member up to 1/2 in maximum to allow for greater construction tolerances. The LRUZ offers an economic alternative for those applications requiring a sloped hanger for rafter-to ridge connections. Used with solid sawn rafters, the LRUZ's unique design enables the hanger to be installed either before or after the rafter is in place. The field-adjustable seat helps improve job efficiency by eliminating mismatched angles in the field and lead times associated with special orders. The LRUZ offers comparable or better load capacity to other rafter hangers at a reduced cost while using fewer fasteners.
RAFTER HANGER ZMAX 18GA 2X8IN U-HANGER DBL SHR GALV 16GA 2X6 PST-FRAME HANGER ZMAX 18GA 2X4
The LRUZ offers an economic alternative for those applications requiring a sloped hanger for rafter-to ridge connections. Used with solid sawn rafters, the LRUZ's unique design enables the hanger to be installed either before or after the rafter is in place. The field-adjustable seat helps improve job efficiency by eliminating mismatched angles in the field and lead times associated with special orders. The LRUZ offers comparable or better load capacity to other rafter hangers at a reduced cost while using fewer fasteners. The HUS is designed for applications where higher loads are needed. This hanger features double-shear nailing that distributes the load through two points on each joist nail for greater strength. This feature allows for fewer nails, faster installation and the use of all common nails for the same connection. The PF is a top-flange hanger designed for common light-frame applications. This economical hanger is for use with 2 x 4 and 2 x 6 members. The double-shear nailing design distributes the load through two points on each joist, providing greater strength with fewer nails.
PST-FRAME HANGER ZMAX 18GA 2X6 U-HANGER DBL SHR GALV 14G 4X10 U-HANGER DBL SHEAR 14GA 4X8IN
The PF is a top-flange hanger designed for common light-frame applications. This economical hanger is for use with 2 x 4 and 2 x 6 members. The double-shear nailing design distributes the load through two points on each joist, providing greater strength with fewer nails. The HUS is designed for applications where higher loads are needed. This hanger features double-shear nailing that distributes the load through two points on each joist nail for greater strength. This feature allows for fewer nails, faster installation and the use of all common nails for the same connection. The HHUS is designed for applications where higher loads are needed. This heavy-capacity hanger features double-shear nailing that distributes the load through two points on each joist nail for greater strength. This feature allows for fewer nails, faster installation and the use of all common nails for the same connection.
U-HANGER DBL SHEAR 14GA 4X10IN U-HANGER 16GA 1-13/16X8-7/8IN U-HANGER DBL SHR GALV 14G 4X12
The HHUS is designed for applications where higher loads are needed. This heavy-capacity hanger features double-shear nailing that distributes the load through two points on each joist nail for greater strength. This feature allows for fewer nails, faster installation and the use of all common nails for the same connection. The HUS is designed for applications where higher loads are needed. This hanger features double-shear nailing that distributes the load through two points on each joist nail for greater strength. This feature allows for fewer nails, faster installation and the use of all common nails for the same connection. The HUS is designed for applications where higher loads are needed. This hanger features double-shear nailing that distributes the load through two points on each joist nail for greater strength. This feature allows for fewer nails, faster installation and the use of all common nails for the same connection.
JOIST HANGER GALV 18GA 4X10IN HEADER HANGER ZN GALV 16GA 6X JOIST HANGER FM GALV 4 X 10IN
The LUS is an easy to install, economical hanger designed for common lumber sizes. This widely used hanger features double-shear nailing that distributes the load through two points on each joist nail for greater strength. This allows for fewer nails, faster installation and the use of all common nails for the same connection. For fast, accurate installation of door and window headers and other cross-members. HH header hangers can speed up the job, strengthen the frame and eliminate the need for trimmers. The HUC is designed for structures requiring additional strength and safety factors. These face-mount joist hangers have concealed header flanges providing cleaner visible lines in exposed conditions. Some models of this heavy-duty hanger can be special ordered with a skewable seat and a seat that slopes as far as up to 45 deg.
JOIST HANGER GALV 14GA 4X10IN JOIST HANGER GALV 14GA 2X12IN JOIST HANGER GALV 14GA 4X12IN
The HU is designed for structures requiring additional strength and safety factors. Some models of this heavy-duty, face-mount hanger can be special ordered with a skewable seat and a seat that slopes as far as up to 45 deg. The HU is designed for structures requiring additional strength and safety factors. Some models of this heavy-duty, face-mount hanger can be special ordered with a skewable seat and a seat that slopes as far as up to 45 deg. The HU is designed for structures requiring additional strength and safety factors. Some models of this heavy-duty, face-mount hanger can be special ordered with a skewable seat and a seat that slopes as far as up to 45 deg.
JOIST HANGER FM GALV 4 X 12IN GIRDER HANGER 3-5/8X10-7/16IN U-HANGER DBL SHR 14GA 5.5X10IN
The HUC is designed for structures requiring additional strength and safety factors. These face-mount joist hangers have concealed header flanges providing cleaner visible lines in exposed conditions. Some models of this heavy-duty hanger can be special ordered with a skewable seat and a seat that slopes as far as up to 45 deg. Simpson Strong-Tie? HGUS hanger is a heavy-capacity joist hanger that utilizes double-shear nailing for added strength. This innovation distributes the load through two points on each joist nail for greater strength. It also allows the use of fewer nails, faster installation and the use of standard nails for all connections. The Strong-Tie? HGUS412 face-mount joist hanger features a G90 galvanized finish for corrosion resistance and requires the use of hot-dip galvanized fasteners which meet the specifications of ASTM A153. The HHUS is designed for applications where higher loads are needed. This heavy-capacity hanger features double-shear nailing that distributes the load through two points on each joist nail for greater strength. This feature allows for fewer nails, faster installation and the use of all common nails for the same connection.
JOIST HANGER FM ZMAX 2 X 10IN GIRDER HANGER 5-1/2X8-15/16IN
The HUC is designed for structures requiring additional strength and safety factors. These face-mount joist hangers have concealed header flanges providing cleaner visible lines in exposed conditions. Some models of this heavy-duty hanger can be special ordered with a skewable seat and a seat that slopes as far as up to 45 deg. The HGUS is an extra-heavy-capacity hanger for applications requiring girder support. This girder hanger features double-shear nailing that distributes the load through two points on each joist nail for greater strength. Value-engineered, the HGUS is designed to carry high-loads for an economical price.
   
 
1